Cameron BARTON 580A Скачать руководство пользователя страница 55

Страница: 55 / 56

A-21

Model 580A Differential Pressure Switch

Appendix A

Product Warranty

A. Warranty

Cameron International Corporation ("Cameron") warrants that at the time of shipment, the prod-

ucts manufactured by Cameron and sold hereunder will be free from defects in material and

workmanship, and will conform to the specifications furnished by or approved by Cameron.

Warranty Adjustment
(1) If any defect within this warranty appears, Buyer shall notify Cameron immediately.
(2) Cameron agrees to repair or furnish a replacement for, but not install, any product which

within one (1) year from the date of shipment by Cameron shall, upon test and examina-

tion by Cameron, prove defective within the above warranty.

(3) No product will be accepted for return or replacement without the written authorization of

Cameron. Upon such authorization, and in accordance with instructions by Cameron, the

product will be returned shipping charges prepaid by Buyer. Replacements made under

this warranty will be shipped prepaid.

C. Exclusions from Warranty

(1) THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER

EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY, OR FITNESS FOR

A PARTICULAR PURPOSE, OR OTHERWISE.

(2) Components manufactured by any supplier other than Cameron shall bear only the war-

ranty made by the manufacturer of that product, and Cameron assumes no responsibility

for the performance or reliability of the unit as a whole.

(3) "In no event shall Cameron be liable for indirect, incidental, or consequential damages

nor shall the liability of Cameron arising in connection with any products sold hereunder

(whether such liability arises from a claim based on contract, warranty, tort, or otherwise)

exceed the actual amount paid by Buyer to Cameron for the products delivered hereun-

der."

(4) The warranty does not extend to any product manufactured by Cameron which has

been subjected to misuse, neglect, accident, improper installation or to use in violation of

instructions furnished by Cameron.

(5) The warranty does not extend to or apply to any unit which has been repaired or

altered at any place other than at Cameron's factory or service locations by persons not

expressly approved by Cameron.

Product Brand

Barton® is a registered trademark of Cameron International Corporation ("Cameron").

Tefzel® is a registered trademark of E.I. DuPont de Nemours & Co., Inc.

Содержание BARTON 580A

























































Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды

Cameron BARTON 580A, Руководство пользователя

Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды