Cameron BARTON 580A Скачать руководство пользователя страница 13

Страница: 13 / 56

Model 580A Differential Pressure Switch

Section 3

Replace the bezel/lens assembly.

HUB

Pointer "slipped"

rotated on hub

Hub held in place

with 1/4" wrench

Figure 3.2—"Slipping" pointer

To test for reverse travel, connect the pressure source to the low-pressure

(LP) housing and vent the HP housing. Apply pressure to approximately

150% of the DP range. The pointer should move approximately 5% to

10% below zero.

To test for overtravel, connect the pressure source to the HP housing and

vent the LP housing. Apply pressure to approximately 150% of DP range.

The pointer should move approximately 5% to 10% above the full scale

mark.

Apply 0, 50, and 100% of full scale pressure. If the indication is within

specified limits, no adjustments are necessary. If the indication is not

within specified limits, perform a complete calibration (see

Indicator

Calibration, page 15

6. Make sure the instrument zero indication is correct; otherwise, repeat

step 2.

Verify the switch set points (refer to

Changing Switch Set Point, page

Pointer Installation and Removal

During adjustment and calibration of the unit, it may be necessary to remove

and reinstall the pointer. See the following procedures for instructions. Note

that the scale plate is split to allow it to be removed without pulling the

pointer.

Pointer Installation

1. Position the pointer on the movement shaft with the pointer set at zero

scale. Obtain 75% to 90% pointer hub engagement on the movement

pinion shaft. The pinion shaft must not extend through the pointer hub. It

may be necessary to enlarge the hub hole using a tapered broach (includ-

ed in the calibration toolkit, Part No. 9A-0288-1032B).

Содержание BARTON 580A

























































Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды

Cameron BARTON 580A, Руководство пользователя

Результаты поиска

Содержание BARTON 580A

Отзывы:

Похожие инструкции для BARTON 580A

Бренды по названию

Популярные бренды