Cameron BARTON 580A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 56

background image

15

Model 580A Differential Pressure Switch

Section 3

To remove the scale plate, move the pointer to the 12 o'clock position, remove

the screws from the scale plate, and gently guide the scale plate halves from

beneath the bottom mounting tab. Screws are located at 12, 3 and 9 o'clock

positions and near the center of the plate which overlays a narrow bracket.

To reinstall the scale plate, repeat the installation steps in reverse order, as

follows. Holding the pointer in the 12 o'clock position, place the scale plate

halves against the top mounting tab and guide the bottom edges behind the

bottom tab. Replace the screws in the top tab and in the center of the scale

plate. No screw is used with the bottom tab.

Indicator Calibration

If the DPU assembly is replaced on a Model 580A differential pressure switch

with indicator, the indicator must be recalibrated. This procedure does not ap-

ply to the 580A-2 blind switch without indicator.

IMPORTANT: Review all Model 224 DPU procedures and WARNINGS/NOTICES in

Appendix A, page A-1,

before performing this procedure.

1. Securely mount the instrument in an approximately level position and

connect the DPU, as described in

Mounting, page A-5

.

2.

Remove the bezel/lens assembly or cover.

3.

Align the linkage between the drive arm and the movement at 50% differ

-

ential pressure (DP) as shown in Figure 3.3. Inspect parts for straightness

and pivot-fit without binding.

Figure 3.4—Range/linearity adjustment (50% DP)

4.

Check the pointer for zero indication. If necessary, set the pointer to zero

by slipping the pointer on the hub, per step 2 of

Calibration Check, page

12

.

5.

Apply 100% pressure. If the pointer exceeds full-scale, adjust the range

adjust screw with a 1/8-in. open-end wrench to lengthen the movement

range arm..

«
...
13
14
15
16
17
...
»

Содержание BARTON 580A

























































Отзывы:

Нет отзывов

Похожие инструкции для BARTON 580A

Бренд: Camozzi Страницы: 2

Бренд: FAAC Страницы: 2

Бренд: Kathrein Страницы: 8

Бренд: Nayar Systems Страницы: 21

Бренд: Kathrein Страницы: 24

Бренд: Kasia Страницы: 5

Бренд: DITEC Страницы: 8

Бренд: Top View Страницы: 2

Бренд: Extron electronics Страницы: 2

A99-BAI-ACSF-UGKIT

Бренд: Westell Страницы: 3

Бренд: SMART Страницы: 46

Бренд: JAR Systems Страницы: 2

Бренд: Surefire Страницы: 2

Бренд: AsGa Страницы: 23

Бренд: Eaton Страницы: 2

Бренд: PKP Страницы: 11

Бренд: PhD Solutions Страницы: 23

Бренд: H3C Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды