background image

CAMEC ELITE PRO

®

 2

 

EM305

Ref: ELITE PRO 2 EM305-0715Rev.A.

5

INSTALLATION - SAFETY GUIDELINES

Read this user manual carefully before installation and use. Failure to comply with these rules 

could result in serious injury or damage to property.

These symbols identify important safety precautions. They mean CAUTION! WARNING! SAFETY 
FIRST! IMPORTANT INFORMATION!

Before starting installation under the caravan:

•  Check the towing load of your vehicle and the gross weight of your caravan in order to establish whether they are 

designed for the additional weight. The manoeuvring system itself has a weight of about 33kg and a battery has a 

weight of about 20-25kg.

• 

Check the minimal installation dimensions of the manoeuvring system based on figure 2.

 

•  Check that the caravan is disconnected from the battery supply and the mains electrical supply.  

•  Only use adapters and accessories that are supplied or recommended by the manufacturer.

• 

Check that the tyres are not worn and do have the same size and design (fitting to new or nearly new tyres is the 

best option).

•  Make sure that the tyre-pressures are correct to the manufacturer’s recommendation.

•  Make sure the chassis is in good condition without any damage and is free from rust, dirt, etc.

•  Stop work immediately if you are in doubt about the assembly or any procedures and consult one of our engineers 

(please refer to contact information on the last page of this manual).

•  Locate the battery isolation switch to be accessible at all times when parking and moving the caravan.

•  Do not remove, change or alter any parts of the chassis, axle, suspension or brake mechanism. Any drilling of 

holes in the chassis is not allowed.

• 

Do not install the unit if you are under the influence of drugs, alcohol or medication that could impair your ability to 

use the equipment safely.

Fig. 2

Содержание Elite Pro2 EM305





















Отзывы: