14
7RSHUIRUPWKH$XWR6HWXSIXQFWLRQÀUVWFRQQHFWWKHVXSSOLHGPLFURSKRQHWR
the front panel 'Mic In' input and place it at your normal listening position in
the room. It should also be placed at normal listening height.
Press the
button on the remote control to access the OSD and then select
the Auto Setup Menu. This will access the "Auto Setup Menu" as below.
Follow the on-screen instructions and press 'Enter' on the remote control
when ready to start the Auto Setup function.
Once activated the OSD will display the message below and the word
$8726(783ZLOODOVREHGLVSOD\HGRQWKHIURQWSDQHORIWKH5WRFRQÀUP
A series of test signals will now be output from all of the connected speaker
terminals of the 351R (including the Subwoofer output).
2QFHÀQLVKHGWKHXQLWZLOOGLVSOD\DVFUHHQVLPLODUWRWKHRQHEHORZUHSRUWLQJ
which speakers were found and any that appear out of phase.
If any speakers appear unconnected or out of phase carefully check the
connections on the speaker and the back of the unit. Also check any bi-wiring
links that might be present on the speaker. For any out of phase speakers
check that the re terminal of the 351R goes to the + terminal of that
speaker and similarly the – terminal of the 351R goes to the – terminal of the
speaker for that channel.
azur 351R
Audio In. Select
Tone/Sub Config.
Speaker Config.
Speaker Distance
Speaker Level
Speaker Xover
Auto Setup
Dolby/DTS Setup
OSD Setup
Quit : [I/O]
Enter : [ENTER]
Please press ENTER to start auto
setup
Auto Setup Menu
Continue : ENTER
Plug the microphone into the Mic. input on the front panel and
place the microphone at normal listening position and height
Auto Setup Menu
The unit is now checking which speakers are connected and their
phase
Please wait...
azur 351R
Continue : ENTER
The speakers that have been found are:
L C R SL SR LB RB SW
All speakers are in phase
If necessary press the
button to perform a retest or press Enter to start
the second part of the auto setup procedure as below.
Again a series of test signals will now be output from all of the connected
speaker terminals and subwoofer. The 351R uses these to measure the
levels and distances (and hence introduce the correct delays) appropriate to
your speakers and room characteristics.
When the auto setup of the 351R is completed successfully, the 351R will
return to the Speaker Setup Menu.
The Speaker Distance and Level Calibration settings for each speaker will
have been updated.
It is of course now possible to go into the Speaker Delay and Level Calibration
PHQXV LI \RX ZDQW WR PDQXDOO\ FKHFNDGMXVW WKH VHWWLQJV PDGH E\ WKH
CAMCAS system, and it is always advisable to check them as no system can
be totally foolproof.
7R H[LW WKH DXWR VHWXS PHQX RI WKH 5 FRQWLQXH WR SUHVV WKH
button
RQWKHUHPRWHFRQWUROWRH[LWDOOPHQXVRUXQWLO26'LVQRORQJHUGLVSOD\HG
on the front panel. You can now unplug the microphone and put it away for
future use.
Note: If the auto setup of the 351R is unsuccessful for some reason a 'Fail'
message will appear on the OSD. Included in this message will be details of
WKHVSHDNHUFKDQQHORUFKDQQHOVZKLFKKDYHQRWEHHQVXFFHVVIXOO\DGMXVWHG
If this is the case, please again check that the speaker or speakers detailed
in the OSD as 'failed' are connected correctly & have not been wired out of
SKDVH$OVRFKHFNWKHPLFURSKRQHFRQQHFWLRQDQGDQ\RWKHUH[WHUQDOLVVXHV
that could have affected the tests such as noise in the room etc.
Note: Like all such systems CAMCAS has some limitations. Speakers that
H[KLELWYHU\VWURQJSKDVHDQJOHVRUGHOLEHUDWHO\ZLUHVRPHGULYHXQLWVRXWRI
phase can of course appear to the system as an out of phase speaker when
correctly connected. If a speaker is reported as out of phase but is correctly
wired please consult the speakers manufacturer in case this is the case.
Similarly bi-polar speakers which radiate in more than one direction can
PDNHLWGLIÀFXOWWRPHDVXUHWKHGLVWDQFHDQGVRPHWLPHVOHYHODFFXUDWHO\DV
\RXPLJKWH[SHFW
In all cases it is always advisable to manually check the settings CAMCAS has
made for a 'reality check' to ensure there are no obvious errors.
Auto Setup Menu
The unit is now measuring the Distance and Level settings for
your speakers
Please wait........
azur 351R
Audio In. Select
Tone/Sub Config.
Speaker Config.
Speaker Distance
Speaker Level
Speaker Xover
Auto Setup
Dolby/DTS Setup
OSD Setup
Quit : [I/O]
Enter : [ENTER]
Please press ENTER to start auto
setup
