Cambridge Air Solutions Blow-Thru SA Series Скачать руководство пользователя страница 41

Страница: 41 / 48

SA-Series Technical Manual

Cambridge Air Solutions

REMOTE CONTROL STATION

CE-SMART

SYSTEM

The CE-Smart system includes a lockable

NEMA 1 enclosure (9"W x 14"H x 5"D)

equipped with a three position selector switch

(Summer Ventilation - Off - Heating); a

combination seven day programmable timer

and thermostat (TSS); an override timer;

intermittent/continuous control; and indicating lights for

blower operation (green), burner operation (red), and

reset (amber).

The operator can control the heater from this panel

provided the heater mounted disconnect is in the “ON”

position and the service switches are in the “REMOTE”

position. The TSS utilizes an encapsulated thermistor to

sense space temperature. The adjustable differential is

set by the selection of the ON and OFF temperatures.

This control can accommodate separately programmed

schedules for both the ventilation and heating modes. See

the operating and programming instructions for the TSS

Controller (page 20).

The intermittent/continuous control allows the heater to

be operated in two modes. During unoccupied hours it

operates intermittently based on a thermostat at maxi-

mum discharge temperature (see EDL - Space Heating

Mode) for space heating. During occupied hours it oper-

ates continuously at modulating discharge temperature

for make-up air (see EDSM - Continuous Make-Up Air

Mode).

REMOTE CONTROL STATION

COMPONENTS

THERMISTOR (RTS)

The thermistor is wired to the temperature

sensor terminal block. If remote location of

the sensor is desired, the connecting cable

must be wired between the thermistor and

this point. The thermistor enclosure (SH-1)

is packed in the remote control station for

shipment. It can be mounted on the exterior sides or

bottom of the remote control station or a remote location

within 500 feet using 18 gauge stranded, twisted-pair,

shielded cable.

GAS CONTROL SYSTEM

The gas control system utilizes

Maxitrol's Series 44 modulation

controls. The discharge temperature

sensor, which is mounted in the

discharge duct, transmits a resistance

signal back to the amplifier that

corresponds to the discharge

temperature. The amplifier creates a

voltage output to drive the modulating valve to maintain

the preselected temperature.

The system can be operated either intermittently as a

space heater at maximum discharge temperature

(EDL - Space Heating Mode) or continuously as a

makeup air heater with the discharge temperature

modulating to maintain the space temperature (EDSM -

Continuous Make-Up Air Mode).

EDL - Space Heating Mode - The discharge temperature

is controlled by the MAX setting on the amplifier

(100-160˚F). The heater cycles on and off based on the

temperature settings of the space thermostat.

EDSM - Continuous Make-Up Air Mode (requires

CE-Smart) - The discharge temperature modulates to

maintain the space temperature selector. The adjustable

temperature selector is typically mounted inside the

remote control station and is set to the desired space

temperature and it transmits a resistance output to the

amplifier to control the discharge temperature. The non-

adjustable space sensor is mounted in the space and

transmits a resistance signal back to the amplifier that

corresponds to the space temperature. The discharge

temperature sensor is mounted in the discharge and

transmits a resistance signal back to the amplifier that

corresponds to the discharge temperature. The amplifier

creates a voltage output to drive the modulating valve to

maintain the selected space temperature by controlling the

heater output between the MIN and MAX setting on the

amplifier. The MIN dial setting determines the minimum

discharge temperature the heater will deliver (40 to 80˚F).

The MAX dial setting determines the maximum discharge

temperature the heater will deliver (100 to 160˚F). When

the space temperature drifts from the temperature selector

setpoint by more than 3˚F, the modulating valve is driven

to the MIN or MAX discharge temperature, as applicable.

INDIVIDUAL COMPONENT DESCRIPTIONS

Содержание Blow-Thru SA Series

















































Результаты поиска

Содержание Blow-Thru SA Series

Отзывы:

Похожие инструкции для Blow-Thru SA Series

Бренды по названию

Популярные бренды

Cambridge Air Solutions Blow-Thru SA Series, Техническое руководство

Результаты поиска

Содержание Blow-Thru SA Series

Отзывы:

Похожие инструкции для Blow-Thru SA Series

Бренды по названию

Популярные бренды