background image

Cambridge Air Solutions

760 Long Road Crossing Dr.

Chesterfield, MO. 63005

Phone: (636) 532-2233

Fax: (636) 530-6133

www.cambridgeair.com

SA-SERIES

BLOW-THRU

®

 SPACE HEATER

TECHNICAL MANUAL

Copyright © 2020 

Cambridge Air Solutions

All Rights Reserved

Contents

Hazard Summary ..............................................................................................................2

General Installation Instructions .......................................................................................3

Uncrating Instructions .......................................................................................................3

Mounting Location ............................................................................................................3

Typical System Overview .................................................................................................4

  Accessory Identification ..................................................................................................4

  Heater Operation .............................................................................................................5

  Heater Configuration ......................................................................................................5

  Roof Top Mounting .........................................................................................................6

  Thru Wall Mounting ........................................................................................................8

  Under Roof Mounting ...................................................................................................10

  Gas Piping .....................................................................................................................12

  Electrical Wiring  ..........................................................................................................13

Start-up Instructions ........................................................................................................14

Shutdown Instructions ....................................................................................................17

Calibration Procedure  ....................................................................................................17

Operating Instructions .....................................................................................................19

  Operating Sequence ......................................................................................................19

  TSS Controller  .............................................................................................................20

Troubleshooting Instructions ..........................................................................................29

  Troubleshooting Guide..................................................................................................29

Reference ........................................................................................................................35

  Electrical Control Enclosure .........................................................................................35

  Electrical Wiring Diagrams ...........................................................................................36

  Electrical Connection Diagram  ....................................................................................38

  Individual Component Descriptions .............................................................................39

  ANSI/ASHRAE/IESNA Standard 90.1 ........................................................................42

Содержание Blow-Thru SA Series

















































Отзывы: