MI182 REV.8 Page 1 of 2
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
ISO 9001:2000
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OK3 – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
combustible materials are always kept at a safe distance from the radiant energy. This heater is
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
combustibles are present. Remember that objects placed under an infrared heater can take a while
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
application, check with the factory for recommendations. Failure to comply can result in personal
injury and/or property damage.
DESCRIPTION
1.0
The OK3 radiant heaters are suitable for comfort heating
use in non-hazardous areas protected from rain, snow or splashing,
where heating element temperatures in excess of 750°C(1382°F)
will not present the risk of fire or explosion. The heater does not
present a safety hazard when it is installed, operated and maintained
in accordance with these instructions.
2.0
The OK3 heater has two U-shaped metal sheath heating
elements factory interconnected in series or parallel depending on
voltage. Never change heaters which have been factory series
connected to a parallel connection.
3.0
Minimum space clearances from combustibles, when
heaters are horizontally mounted and installed, as listed in Table 1
following.
Table 1
Min. Spacing
From nearest wall
600 mm (24”)
From the ceiling
300 mm (12”)
INSTALLATION
The system designer is responsible for
the safety of this equipment and
adequate back-up controls and safety
devices must be installed. Failure to
comply could result in personal injury
and/or property damage.
Heaters must be wired by qualified
personnel in compliance with local
codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on the
product label.
Insulation contamination or moisture
accumulation can cause fault to the
element sheath generating arcing and
releasing molten metal. Install proper
ground fault protection to prevent
personal injury and/or property
damage.
6.0
The connection box volume is 3100 cm³(190 in³).
7.0
Supply conductors to the heater must be suitable for
110°C(230°C). The ground wire from the supply shall be connected
to the grounding connection located in the connection box.
8.0
The connection box has eight dual knockouts, ½" or ¾"
and two dual knockouts ¾" or 1". The standard Type 1 enclosure
is suitable for dry, indoor locations only in non-corrosive
environments.
9.0
For short circuit protection, heaters must be installed with
proper fast acting fuses or breakers as close as possible to the
ratings indicated on the nameplates, in compliance with the local
electrical codes.
4.0
To facilitate mounting, the heater has four ¼"-20 mounting
holes located at each top corner of the housing. Either chain
mounting (use eye bolts) or bolting to a non-combustible sliding
support (slotted holes) is adequate provided that the spacing
instructions as given in 3.0 are followed. Chain mounting is preferred
since rigidly mounted heaters are susceptible to warping.
38 cm
[15”]
60 cm
[24”]
30
cm
[12”
]
FIG. 1 – MOUNTING CLEARANCES
MI182 REV.8 Page 1 of 2
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
ISO 9001:2000
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OK3 – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
combustible materials are always kept at a safe distance from the radiant energy. This heater is
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
combustibles are present. Remember that objects placed under an infrared heater can take a while
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
application, check with the factory for recommendations. Failure to comply can result in personal
injury and/or property damage.
DESCRIPTION
1.0
The OK3 radiant heaters are suitable for comfort heating
use in non-hazardous areas protected from rain, snow or splashing,
where heating element temperatures in excess of 750°C(1382°F)
will not present the risk of fire or explosion. The heater does not
present a safety hazard when it is installed, operated and maintained
in accordance with these instructions.
2.0
The OK3 heater has two U-shaped metal sheath heating
elements factory interconnected in series or parallel depending on
voltage. Never change heaters which have been factory series
connected to a parallel connection.
3.0
Minimum space clearances from combustibles, when
heaters are horizontally mounted and installed, as listed in Table 1
following.
Table 1
Min. Spacing
From nearest wall
600 mm (24”)
From the ceiling
300 mm (12”)
INSTALLATION
The system designer is responsible for
the safety of this equipment and
adequate back-up controls and safety
devices must be installed. Failure to
comply could result in personal injury
and/or property damage.
Heaters must be wired by qualified
personnel in compliance with local
codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on the
product label.
Insulation contamination or moisture
accumulation can cause fault to the
element sheath generating arcing and
releasing molten metal. Install proper
ground fault protection to prevent
personal injury and/or property
damage.
6.0
The connection box volume is 3100 cm³(190 in³).
7.0
Supply conductors to the heater must be suitable for
110°C(230°C). The ground wire from the supply shall be connected
to the grounding connection located in the connection box.
8.0
The connection box has eight dual knockouts, ½" or ¾"
and two dual knockouts ¾" or 1". The standard Type 1 enclosure
is suitable for dry, indoor locations only in non-corrosive
environments.
9.0
For short circuit protection, heaters must be installed with
proper fast acting fuses or breakers as close as possible to the
ratings indicated on the nameplates, in compliance with the local
electrical codes.
4.0
To facilitate mounting, the heater has four ¼"-20 mounting
holes located at each top corner of the housing. Either chain
mounting (use eye bolts) or bolting to a non-combustible sliding
support (slotted holes) is adequate provided that the spacing
instructions as given in 3.0 are followed. Chain mounting is preferred
since rigidly mounted heaters are susceptible to warping.
38 cm
[15”]
60 cm
[24”]
30
cm
[12”
]
FIG. 1 – MOUNTING CLEARANCES
MI102 REV.7 Page 6 of 6
F
IG.
5E - 208
OR
240 V
OLT SINGLE PHASE WITHOUT CONTROLS
208
OU
240 V
OLT MONOPHASÉ SANS CONTRÔLES
F
IG.
5F - 208
OR
240 V
OLT SINGLE PHASE WITH CONTROLS
208
OU
240 V
OLT MONOPHASÉ AVEC CONTRÔLES INCORPORÉS
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
TM
MI102 REV.7.01 Page 6 of 8
