Calix GigaSpire BLAST u12 Скачать руководство пользователя страница 31

Страница: 31 / 38

Proprietary Information: Not for use or disclosure except by written agreement with Calix.

LED States - GigaSpire Turn-up

The LED's located on the corner of the unit provide information on the status and current

state of the device. Below, you will find a detailed status of the power-up cycle.

Unit Status

Power-up

Status

Function

LED Status

Off

Power is off.



The unit has not been turned on or



There is no power to the unit or



The UPS battery has been

discharged and there is insufficient

power to continue operation.

Note:

LED is off.

876

Booting Up,

Software Upgrade in

Process

Unit is in the boot-up process or

service/software is being upgraded.

Flashes orange every second assuming

software has taken over.

Note:

LED is on.

875

Boot-up Failure

Boot-up failed (assuming software has

taken over)

Note:

Cycles at 8/10 of a second

Note:

LED is on.

876

Connected to

Internet

Unit has successfully booted up, local

services are up, and connected to the

Internet.

Note:

LED is on.

876

Service Failure, No

Internet

No service, no Internet.

Note:

LED is on.

Notes:

Cycles at 1.6 seconds

876

Alexa has been

triggered, Alexa is

listening

Alexa is listening and active. Listing

once the trigger word is heard.

Note:

LED is on.

Note:

Cyan on continuously.

876

Содержание GigaSpire BLAST u12







































Результаты поиска

Содержание GigaSpire BLAST u12

Отзывы:

Похожие инструкции для GigaSpire BLAST u12

Бренды по названию

Популярные бренды

Calix GigaSpire BLAST u12, Руководство по установке

Результаты поиска

Содержание GigaSpire BLAST u12

Отзывы:

Похожие инструкции для GigaSpire BLAST u12

Бренды по названию

Популярные бренды