background image

1

PRODUCT SPECS

WARNING 

To reduce the risk of  INJURY or DEATH: 

• Never let  children  operate  the  gate  or  play  around the  gate. Keep the remote control away

from children.

• Always keep people and objects away from the gate. Cars, people, and other objects should

never enter when the gate is closing.

• Test  gate operator monthly. The  gate must  reverse when it comes in contact  with a solid

object, or stop when an object activates the non-contact sensors. After adjusting the force or

travel limit, re-test the gate operator. Failure to maintain the gate operator properly can

increase the risk of injury or death.

• Use the emergency release only when the gate is not moving.

• Keep  the  gate  properly  maintained.  Read  the  owner's manual on how to maintain your gate.

Have a certified service technician make repairs or install gate operator hardware.

• The gate entrance should be used for vehicles only. Pedestrians should use a seperate entrance.

• Keep these instructions.

Voltage Input: 110V 

Maximum Output Current: 15 amp, Fuse: AC 110V 15 amp 

Remote Control Distance: >150 Feet (50 meters) 

Maximum Gate Weight: 2500 lbs

Maximum Gate Length: 25 Feet

• Verify this operator is proper for the type and size of gate.

• Make sure the gate has been properly installed and slides freely in both directions. Repair

or replace all worn or damaged gate hardware prior to installation.

Product Specs

Содержание CM7-ACFP


















Отзывы: