background image

CALIFORNIA ACCENT LIGHTING, INC.

2820 E. Gretta Lane, Anaheim, CA 92806
ph. 800.921.CALI (2254) | fx. 714.535.7902 | [email protected] | calilighting.com

© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.

5 / 20 / 2021 / Rev 3

Page 16 of 20

ALS

500T-SWM-MI

INSTALLATION INSTRUCTIONS

Connecting Continuous Runs

Allen Screw

Continuous Connector

Lock Washer

Sequence Labeling

Male Block

Quick

Disconnects

Sequence Labeling

Female Block

Extrusions aligned

Tighten with allen wrench

Make cuts to extrusion and lens if necessary. Do not cut PCB, wiring, or 
accessories. Only use a miter saw equipped with a blade for cutting metal.

Note:

 If applicable, remove Connector Blocks from extrusion before cutting.

1

Position luminaires together and align the screw of the Male Block to meet the 
Female Block. Tighten Allen Screws using provided Allen Wrench to close the 
gap until luminaires meet. Only tighten screws until extrusion edges meet with 
no gaps. Over-tightening screws will create separation at the seam.

Tip:

 One person holds the luminaire together, ensuring there is no gap, while 

another person tightens screws.

3

If applicable, insert one Allen Screw with Lock Washer into each Male Block.

Note:

 Ensure sequence labeling is in the correct sequence (A, B, C, etc.)

2

Connect disconnects between luminaires, if applicable. Ensure connected runs 
do not exceed load of power supply.

Note:

 Refer to Electrical section on first page for details on calculating load.

4

Содержание ALS500T-SWM-MI





















Отзывы: