Caen ELS LiAM 6005 Скачать руководство пользователя страница 8

Страница: 8 / 85

LiAM User’s Manual

Read over the instruction manual carefully before using the instrument.
The following precautions should be strictly observed before using the LiAM:

WARNING



Do  not  use  this  product  in  any  manner  not
specified  by  the  manufacturer.  The  protective
features of this product  may  be impaired if it is
used in a manner not specified in this manual.



Do not use the device if it is damaged. Before
you use the device, inspect the instrument for
possible cracks or breaks before each use.



Do not operate the device around explosives gas,
vapor or dust.



Always use the device with the cables provided.



Turn off the device before establishing any
connection.



Do not operate the device with the cover
removed or loosened.



Do not install substitute parts or perform any
unauthorized modification to the product.



Return the product to the manufacturer for
service and repair to ensure that safety features
are maintained

CAUTION



This instrument is designed for indoor use and in
area with low condensation.

Содержание LiAM 6005





















































































Результаты поиска

Содержание LiAM 6005

Отзывы:

Похожие инструкции для LiAM 6005

Бренды по названию

Популярные бренды

Caen ELS LiAM 6005, Руководство пользователя

Результаты поиска

Содержание LiAM 6005

Отзывы:

Похожие инструкции для LiAM 6005

Бренды по названию

Популярные бренды