background image

14

Control Wiring

Thermostat wires should be used for control wiring between the

indoor and outdoor units. A two conductor cable is required for the

cooling only units and a four conductor cable is required for heat

pumps.
The control circuit is 24 volts AC (minimum 40VA) supplied from

the indoor unit.

1. Make sure you have enough control wires to cover the

distance between the indoor and outdoor unit.

2. Route one end of the control wiring through the opening

provided in the unit side panel and connect to the control

terminal strip using either Fig. 28 for AC units or Fig. 29
for Heat Pump units.

A150280

Fig. 28 – 40MKCB**F/24AHA4 or 124ANS Connecting

Diagram

A150282

Fig. 29 – 40MKQB**F/25HHA4 or 224ANS Connecting

Diagram

Strain Relief Bracket for Indoor Units

A strain relief is included within the indoor unit’s packaging. This

is required to be installed. The strain relief bracket and location to

where this should be affixed on the unit’s body is shown in Fig. 30

and 31.

Note: dimensions are in millimeters (mm)

A150308

Fig. 30 – Strain Relief Bracket

Strain Relief Bracket Location

A150307

Fig. 31 – Strain Relief Bracket Affixed to Under Ceiling Body

Содержание 40MKCF



























Отзывы: