Cablescan 90 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 57

background image

Page 30

Series 90 Setup Manual

COMMAND BUTTONS

TestDiag has three command buttons: Diag, Adv, and Reset. A command can also be selected
by pressing the letter key that is underlined in the button.

Diag

The Diag button is used to begin a diagnostic test. If a high-voltage tester is connected, make
sure all hands are clear of tester before clicking Diag button.

Adv

The Adv button is used to open an Advanced Functions dialog
box. The advanced functions are as follows:

Download Firmware

Download Firmware is used to download the Scanner Control
Board (SCB) software, from disk to the EEPROM on the
board. TestRite automatically checks the firmware in the SCB
during initialization, and if the firmware requires updating, a
message box opens and provides a button to download the new firmware. The Download
Firmware function in this dialog box can be used to force the firmware to be downloaded.

Warning

Interrupting the tester or PC during download can cause the download
portion of the EEPROM to corrupt. If this happens, a new EEPROM must
be installed on the Scanner Control Board. Contact the factory.

Capacitance Offset Function

Capacitance Offset Function measures the amount of capacitance in the system. This value is
used as an offset to the measurements made during test to improve capacitance measurement
accuracies. This function needs to be run only when the values being measured are below
1000 pf.

Set Voltage Type

Set Voltage Type is for high-voltage systems. The Series 90HV originally had a maximum
isolation test voltage of 1000 vdc. This was later increased to 1500 vdc. This value should be
set according to the tester connected. After the tester has the latest firmware downloaded, this
value will automatically be set by the software.

Reset

The Reset button aborts the test and reinitializes the tester and communications link.

«
...
38
39
40
41
42
...
»

Содержание 90 Series


























































Отзывы:

Нет отзывов

Похожие инструкции для 90 Series

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: KaVo Страницы: 16

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: Makita Страницы: 10

4 Happy Kids GUCIO

Бренд: 4iQ Страницы: 12

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: GALBIATI Страницы: 20

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды