Cablescan 90 Series Скачать руководство пользователя страница 28

Страница: 28 / 57

Page 18

Series 90 Setup Manual

5210982 Cable Assembly

The 5210982 discrete-wired cable assembly (Figure 17) has a 64-pin AMP Champ IDC
connector (7200449) on the first end and unterminated on the second end. This connector can be
mounted on the interface fixture and used to wire the mating connectors.

7200449

5210982

Figure 17. Low- voltage Cable Assembly – 5210982

Note:

The 7200449 is an IDC-type connector that uses special terminating
tools when used without the cable. Refer to AMP literature for
termination tools.

Low-voltage Interface Cable Assemblies

CS P/N

Description

First End

Connector

Second End

Connector

5210914-3

64-conductor flat cable

7200481

(no connector)

5210917-3

64-conductor flat cable

7200481

7200446

5210982

64-conductor Harness Board

(discrete)

7200449

(no connector)

Cablescan to AMP Conversion Table

Cablescan

Part No.

Description

AMP

Part No.

7200426

64-pin latch and eject header, PCB connector

1-499141-2

7200446

64-pin male AMP Champ flat cable connector

552933-1

7200449

64-pin female AMP Champ IDC connector

2-552277-1

7200481

64-pin flat cable socket connector
Strain relief part number

1-746288-2
1-499252-3

Low-voltage Cables and Components

Содержание 90 Series


























































Результаты поиска

Содержание 90 Series

Отзывы:

Похожие инструкции для 90 Series

Бренды по названию

Популярные бренды

Cablescan 90 Series, Руководство по установке

Результаты поиска

Содержание 90 Series

Отзывы:

Похожие инструкции для 90 Series

Бренды по названию

Популярные бренды