background image

 

 
16 
 

Diagram 12 continued 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
How to use diagrams 10,11 and 12: 

If you wished to avoid detecting ring pulls and small ferrous objects (e.g. nails) then you 
would set the NOTCH at 4 and the DISC control at 2. 

 
The effect would be: 

Ring pulls 

 

 

no sound 

Nails 

 

 

-

 

 

no sound 

5p/milk 

bottle top 

-

 

 

high 

volume 

 

£1 coin 

etc. 

 

-

 

 

high 

volume 
 

Note: 

Take 

care not to 

inadvertently 

leave 

the NOTCH in 

the 

ACCEPT 

position 

as the detector, 

when in 

MOTION, will 

detect 

only over the 

small 

range within the 

NAIL            SMALL              MILK           5p COIN       RING PULL      £1 COIN

HORSESHOE   BOTTLE TOP

DETECTED

NO

SOUND

10

8

6

4

2

DISC
SETTING

 

ACCEPT

NO

SOUND

NAIL            SMALL             MILK           5p COIN      RING PULL      £1 COIN

HORSESHOE   BOTTLE TOP

NOTCH SETTING

OFF

2

4

 

Although the CS4ZX is manufactured to the highest specification, slight variations 
can occur in all electronic equipment. This chart, therefore is intended as a guide 
only and precise setting for maximum performance will be achieved by constant 
practice. 

Содержание CS4ZX


























Отзывы: