background image

 

 

19

 
 

ACCESSORIES (OPTIONAL) 

 

Available from C-Scope 

 

Headphones: 

 

Headphones not only extend battery life but improve sensitivity by cutting extraneous noise. The 
headphones should be fitted with a standard stereo 1/4 inch (6.35mm) jack plug. The headphone 
socket is located under the protective cap in the battery housing. 

 
Mini searchhead: 

 

The mini searchhead can be used in place of the supplied head for searching in heavily trashed sites. 
The depth penetration is reduced slightly. When using the mini head operate with the frequency 
switch in position 2. 

Rechargeable battery pack: 

 

A shrink wrapped pack of 8 rechargeable nicad batteries to replace the standard batteries and 
holder. 
 

Battery charger: 

 

The C-Scope battery charger is designed to charge the rechargeable pack quickly and safely. 
 
 

CHARGING BATTERIES 

 
A battery charge socket is provided for use with the C-Scope battery charger (see Accessories) and 
is located under the protective cap in the battery housing. (The smaller of the two sockets.) Inserting 
the charger will automatically remove the power from the detector so the charger must be removed 
to do a battery check. Do not attempt to recharge standard batteries. It will take between eight and 
fifteen hours to fully recharge flat batteries with the C-Scope charging unit. 
 
For further information, and a price list, for all C-Scope accessories please telephone (0233) 
629181. 
 
 

THE IMPORTANCE OF THE RIGHT APPROACH 

 
Treasure hunting can be a profitable and rewarding hobby, if approached in a patient and diligent 
manner. Time spent researching to locate a worthwhile site for a search can be time wasted if your 
search is hasty and erratic. To achieve maximum results it is important then, to decide on your 
approach to any particular site in advance of the actual search. 
 

Содержание CS4ZX


























Отзывы: