background image

 

 
12 
 

This control allows the user to optimise the detector for use on each site. This is 
achieved by reducing the effect of natural mineralisation sometimes found in the ground, 
but it must be individually set for each ground type. 
In high performance detectors, like your CS4ZX, mastering this control is essential to 
gain the full capabilities. 
 
The range provided should allow accurate setting to exclude from the most neutral 
ground through to more 'mineralised' ground. This control is used in conjunction with the 
INLAND/BEACH switch described in B.i. above. 

 
iii. 

METER FUNCTION SWITCH (P in diagram 7). 

This is a three position switch located on the front panel in the central position and is 
labelled METER DISC/GROUND/BATTERY. It allows the user to select which 
information the meter will display. 

 
 

Diagram 9   

Meter Function Switch

 

a. METER DISC 

In this position the meter responds to signals by referring to the pre-programmed 
discriminating channel of the detector. After retuning the needle will normally be in 
the centre of the scale. The needle will move to the left for iron and small pieces of 
aluminium foil, i.e. a negative response, and stay central or move to the right for 
other targets, i.e. a positive response. 

 
b. GROUND 

With the switch in this position the meter shows the responses from the variable 
ground excluding channel of the detector. The meter will show no response to 
ground mineralisation when the BEACH/INLAND switch and the GROUND 
rotary control have been correctly set. When correctly set, all targets will produce 
a positive response on the meter, i.e. the needle will always move to the right. 
Note: in the BEACH setting, items of iron can give a negative response at high 
settings of the GROUND control. 
 
This facility is provided for setting the GROUND control. The control should be 
adjusted until the proximity of the ground causes no movement of the needle. The 
detector should be retuned before the head is presented to the ground after each 

CS4ZX

CS4ZX

CS4ZX

a) Meter Disc

b) Ground

c) Battery

 

Содержание CS4ZX


























Отзывы: