BYD L3
AUTO Owner’s Manual
7-12 Self-maintenance
- Reinstall the oil filling plug.
- Tighten torque: 18~24Nm
2.Oil level checking procedure
Range of application: all of the other
checking and filling (oil level checking,
filling again
……)
The proper checking method for fuel
level is shown as follows, after filling
oil for the first time(If need to filling
again
for
maintenance
or
oil
replacement etc, check the oil level
refer to Oil filling instruction and the
procedures below )
- Start the engine and run it at an idle
speed for at least 10 seconds (notes:
it is normal to hear the sound caused
by air circulation in the system when
starting.)
- Switch to different gears by gear
shift lever (park - reverse - neutral -
driving) and stay for 5 seconds on
each gear before switching to the next
gear.
-
Switch to ―D‖ (Drive)
- Loosen the brake pedal
- Reduce speed to min 60 km/h (do
not exceed 2500rpm)
- Loosen the accelerator until you stop
the car (the noise made by air
circulation
when
starting
will
disappear).
- Heat the gasoline; be careful to drive
at least for 5 minutes or wait until the
temperature of transmission reaches
60
℃
.
- Stop the car on flat ground or slope.
- Step on brake pedal.
- Wait for 2 seconds.
-
Switch the gear to ―R‖ (Neutral).
- Wait for 10 seconds.
-
Switch the gear to ―P‖ (Park).
- Run the engine at an idle speed.
- Pull out the oil level screw plug.
- Make sure you pull out the oil level
screw plug and then at least 0.2 liter
oil will be drained from the oil pipe. (or
it indicates the initial oil is insufficient)
- Wait for a few minutes until the oil
begins to drop from the oil level screw
plug mouth.
- Put the lid on the oil level screw
plug again.
- stop the engine
Check Cooling Fluid Level in
Engine
Check the transparent overflow tank
of the cooling fluid when the engine is
cold. If the cooling fluid level is
located between ―FULL‖ and ―LOW‖
line on the tank, it is in compliance
with the requirement. If the fluid level
is low, additional cooling fluid shall be
added. (Refer to section ―
Choose
Cooling Fluid
‖ below for information
on usable type of cooling fluid.)
The cooling fluid level in the overflow
tank varies with the temperature of
the engine. But if the fluid level is
under ―LOW‖ line, more fluid shall be
added until fluid level reaches ―FULL‖
line.
After adding cooling fluid, if the fluid
level drops in short period, there may
be leakage in the system. You shall
conduct visual check to radiator, hose,
radiator cap, drain cock and pump.
If visual check can not find out
leakage, please contact BYD service
station to check cap pressure and
Содержание L3 AUTO
