BYD L3 AUTO Скачать руководство пользователя страница 171

Страница: 171 / 202

BYD L3

AUTO Owner’s Manual

Self-maintenance 7-5

NOTE

◆

Remember, storage battery

and ignition coil bears high
current or high voltage. Pay
attention to short circuit caused
by accidents.

◆

If the coolant overflows, you

must wash it with water, to
avoid

damaging

the

components or paint finish.

◆

Do not drop any dirt or any

other things into the spark plug
hole.

◆

Do not lever up the external

electrode of spark plug at the
side of central electrode.

◆

You can only use the specified
spark plug. Using other spark
plug may damage the engine or
generate radio interference.

◆

Do not fill too much power

steering fluid, or the power
steering gear may be damaged.

◆

If the brake fluid overflows,

you must wash it with water, to
avoid

damaging

the

components or paint finish.

◆

Do not drive with the air filter

taken down, otherwise it may
cause excessive wear of engine
and meanwhile backfire will
cause

fire

the

engine

compartment.

◆

Notes: do not scratch the

glass by the wiper bracket.

◆

In closing the engine cover,

check if any tools or cloths are
left in the engine compartment.

Location of Jack

Front

Back

Содержание L3 AUTO











































































































































































































Результаты поиска

Содержание L3 AUTO

Отзывы:

Похожие инструкции для L3 AUTO

Бренды по названию

Популярные бренды

BYD L3 AUTO, Руководство пользователя

Результаты поиска

Содержание L3 AUTO

Отзывы:

Похожие инструкции для L3 AUTO

Бренды по названию

Популярные бренды