BYD L3 AUTO Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 202

background image

BYD L3

AUTO Owner’s Manual

7-10 Self-maintenance

Check Fluid Level in Gearbox

Manual Gearbox

1. Check Fluid Level in BS15 Gearbox

Check the fluid level in gearbox when
transmission

is

at

the

normal

operating temperature of 80

℃

with

the  car  parking  on  flat  ground.
Remove the bolt of fluid filler opening
of  the  transmission,  and  touch  the
fluid  level  within  the  bolt  hole  with  a
finger  carefully.  The  fluid  level  shall
reach the edge of the bolt hole. If not,
please  add  original  MTF  (manual
transmission fluid) from BYD until the
fluid  overflow  from  the  filler  opening.
At  last,  install  back  and  tighten  the
bolt of the fluid filler opening.

Clean

up

overflowing

fluid

immediately    as it may damage parts
in the engine compartment.

If  original  MTF  is  not  available,  you
can  use  API  certified  gear  oil  as
substitute.  For  specific  specifications,
please  refer  to

Maintenance Manual

or contact BYD service station.

Transmission  fluid  shall  be  replaced
by  mileage  or  interval  as  specified  in
Periodic  Maintenance  Table.  The
existing  transmission  fluid  shall  be
drained  completely  before  filling  new
transmission fluid.

Please  contact  BYD  service station  if
you  have  any  doubt  about  checking
fluid level or filling fluid in gearbox.

Oil filling plug

Position of oil filling plug

Transmission

fluid

Level of gear fluid

«
...
174
175
176
177
178
...
»

Содержание L3 AUTO











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L3 AUTO

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Бренд: Carefree Страницы: 12

Sprinter Bed System Adventure Wagon Kit

Бренд: FVC Страницы: 8

Polaris TATOU 4S

Бренд: Camoplast Страницы: 13

Бренд: Porsche Страницы: 313

Бренд: BURY Страницы: 2

Бренд: Subaru Страницы: 19

Бренд: Paccar Страницы: 63

Бренд: BMW Страницы: 40

Бренд: Whispbar Страницы: 77

Бренд: MMD Страницы: 3

Бренд: Audi Страницы: 4

Бренд: Thule Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды