BYD e6A Скачать руководство пользователя страница 168

Страница: 168 / 195

BYD e6A AUTO Owner's Manual

5-8 Motor and Chassis

Replace lubricant for front drive
transmission

After running in a new transmission, drain

the lubricant in the transmission case and

refill with fresh lubricant. Unscrew the drain

bolt 1 to drain the lubricant and tighten it

again. Then unscrew the filler bolt 2 to refill

fresh lubricant. SAE80W-90 is

recommended for use; When the outside air

temperature is lower than -15 °C,

SAE75W-90 is recommended for use.

Please keep the filling amount at about 3.5L.

It is recommended to replace lubricant at

the specified service station.

Check lubricant for front drive
transmission

Check the lubricant amount in the transmission

case during daily operation. Remove the filler

plug, and touch the fluid level in the bolt hole.

The normal level should be up to the edge of the

plug hole. Otherwise, please refill fresh lubricant

until it over flows from the filler opening. Then

screw the filler plug and tighten it. Replace the

lubricant in the transmission case regularly.

To secure the quality of lubricant, wash and

clean the transmission case before

replacing lubricant.

Check the bolts outside of the transmission

for looseness or absence during daily

operation. If a bolt found is found loose,

tighten it timely; if there is any bolt missing,

reinstall it. Keep the bolt and transmission

case clean to facilitate heat dissipation.

Transmission fluid

Gear oil level

1. Drain plug

2. Filler plug

Содержание e6A




































































































































































































Результаты поиска

Содержание e6A

Отзывы:

Похожие инструкции для e6A

Бренды по названию

Популярные бренды

BYD e6A, Руководство пользователя

Результаты поиска

Содержание e6A

Отзывы:

Похожие инструкции для e6A

Бренды по названию

Популярные бренды