BYD e6A Скачать руководство пользователя страница 64

Страница: 64 / 195

BYD e6A AUTO Owner's Manual

1-46 Seats, seat belts and airbags

Airbag Warning Indicator

Airbag system is monitored by ECU and

integrates self-diagnosis function. Its status is

indicated by warning indicator on instrument

panel.

●

After the power switch is turned on every

time, the airbag warning light will be on for

about 5 s and then be off for over 5 s,

which indicates that the system is normal.

●

If the airbag is disabled by BYD service

station, the warning indicator still

functions as described in the above

procedure, but it does not provides

protection any more.

This warning indicator is intended to monitor

airbag ECU, impact sensor, air inflation

device, warning light, connecting wire and

power supply. (For details, please refer to

"Service Reminder Indicators and Warning

Buzzer" in Section 1-1)

NOTE

If any of the following conditions, airbag

system may have trouble:

●

After the power switch is turned on, the

warning indicator is not on.

●

After the power switch is turned on, the

warning indicator is still on after 5 s or

flashes and is on again after it is off.

●

After the power switch is turned off, the

warning indicator is on again.

●

The indicator turns on or flashes in

driving.

Tips

If any trouble with airbag system, please

send the car to BYD service station for

check and repair. Or in case of an accident,

the airbag system can not provide

protection as designed.

Airbag Triggering Conditions

The airbag is designed to be triggered under

the following conditions: severe frontal

collision accidents and some special collision

accidents.

In case of minor front collision, side collision,

rear collision or roll-over, generally airbag

system won't be triggered. In such accidents,

the seat belt, if fastened, can protect the

driver and passenger in the normal way.

The decisive factor for triggering the airbag

system is the result of judgment through

comprehensive intelligent comparison of the

deceleration curve, which is produced in a

collision and acquired by the electronic

control unit (ECU), with the set value. If the

signals, such as deceleration, produced and

Содержание e6A




































































































































































































Результаты поиска

Содержание e6A

Отзывы:

Похожие инструкции для e6A

Бренды по названию

Популярные бренды

BYD e6A, Руководство пользователя

Результаты поиска

Содержание e6A

Отзывы:

Похожие инструкции для e6A

Бренды по названию

Популярные бренды