Bush Hog RTX85G Скачать руководство пользователя страница 28

Страница: 28 / 72

ASSEMBLY

RTXG SERIES TILLER 5/19

Assembly Section 3-2

Bush Hog RTXG series Tillers are shipped from the factory partially assembled in a shipping crate and requires

some assembly before being placed into service.

Follow these instructions listed to safely remove the Tiller from the shipping crate and prepare for assembly

1. With the tiller still in the shipping crate, place it on a hard level surface.

2. Remove the crating top and sides and discard.

3. Remove the driveshaft and the Mast Frame

assembly from the shipping assembly and lay

aside for installation later.

4. Insert a lifting strap in the gearbox mounting

frame.

5. Carefully lift the tiller assembly from the

shipping pallet.

6. Remove parking stand from storage position

and place in parking position. (Fig. 3-2A)

7. Place tiller on hard level surface for assembly and remove lift strap.

8. Remove the 10 bolts, Lockwashers and Nuts, 5 on each side, from the strongbacks on the top of the

mainframe. Retain fasteners for re-installation of the Mast Frame to the mainframe.

9. Place the Mast Frame between the strongbacks on the mainframe so the cut outs straddle the driveline

tube and align the bolt holes. (Figure 3-2B)

10. Re-install the fasteners and torque the fasteners per the settings in the torque chart in the back of this

manual.

Содержание RTX85G









































































Результаты поиска

Содержание RTX85G

Отзывы:

Похожие инструкции для RTX85G

Бренды по названию

Популярные бренды

Bush Hog RTX85G, Руководство оператора

Результаты поиска

Содержание RTX85G

Отзывы:

Похожие инструкции для RTX85G

Бренды по названию

Популярные бренды