![background image](http://html1.mh-extra.com/html/bush-hog/rtx85g/rtx85g_operators-manual_2834873056.webp)
OPERATION
RTXG SERIES TILLER 5/19
Operation Section 4-24
O
PE
R
AT
IO
N
© 2020 Alamo Group Inc.
Never run the Tractor engine in a closed building or without adequate ventilation. The
exhaust fumes can be hazardous to your health.
(SG-23)
Transport only at speeds where you can maintain control of the
equipment. Serious accidents and injuries can result from operating this
equipment at high speeds. Understand the Tractor and Implement and
how it handles before transporting on streets and highways. Make sure the Tractor steering
and brakes are in good condition and operate properly.
Before transporting the Tractor and Implement, determine the proper transport speeds for
you and the equipment. Make sure you abide by the following rules:
Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly
to determine the stopping characteristics of the Tractor and Implement. As you increase
the speed of the Tractor the stopping distance increases. Determine the maximum
transport speed not to exceed 20 mph (30 kph) for transporting this equipment.
Test the equipment at a slow speed in turns. Increase the speed through the turn only after
you determine that the equipment can be operated at a higher speed. Use extreme care
and reduce your speed when turning sharply to prevent the tractor and implement from
turning over. Determine the maximum turning speed for you and this equipment before
operating on roads or uneven ground.
Only transport the Tractor and Implement at the speeds which allow you to properly control
the equipment.
Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes
or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance
increases: use extreme care and reduce your speed. When operating in traffic always use
the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you
and watch out for the other guy.
(SG-19)
Before transporting the tractor and implement, idle
the tractor engine, disengage the PTO and wait for
all implement moving parts to come to a complete
stop. Once all implement parts are completely
stopped, raise the implement to transport height.
NOTE:
When raising the implement, maintain 1”
clearance between the driveline and implement
deck. If additional implement deck height is
needed for transport, disconnect the driveline from
the tractor and secure its end to the implement
deck. The implement can then be raised to the
maximum lift height.
OPS-T-0011
Содержание RTX85G
