![background image](http://html1.mh-extra.com/html/bush-hog/rtx85g/rtx85g_operators-manual_2834873038.webp)
OPERATION
RTXG SERIES TILLER 5/19
Operation Section 4-6
O
PE
R
AT
IO
N
© 2020 Alamo Group Inc.
3.3 Tractor Horsepower
The power required to operate an implement is determined by the tractor PTO horsepower. For most operating
conditions, implement requires a tractor with at least 60 HP. Operating the implement with a tractor that does
not have adequate power may damage the tractor engine. Exceeding required HP may cause implement
damage by overpowering the unit.
3.4 3-Point Hitch
The tractor 3-Point Hitch must be rated to lift the
total weight of the implement attached. These tillers
are designed to be mounted on a tractor with a CAT
I or CAT II 3-point hitch. Refer to the tractor
operator’s manual for the category of the tractor
being used. If the hitch does not conform to ASABE
CAT I or CAT II dimensions, the tiller may not fit or
raise properly. Consult an authorized dealer for
possible modification procedures to mount non-
conforming hitches.
Depending on the hitch category, certain size pins
are used to attach the implement to the tractor. CAT
I hitches require 7/8” lower hitch pins and a 3/4” pin
at the top link connection. CAT ll hitches require 1-
1/8” lower hitch pins and a 1” pin at the top link
connection
CAT I Implement / Hitch Specification
CAT II Implement / Hitch Specification
Width from outside to outside A-frame..............26-7/8”
Width from outside to outside A-frame ................. 32-3/8”
Quick hitch width inside lug to lug.....................27-1/8”
Quick hitch width inside lug to lug ........................ 33-5/8”
Height from bottom hitch pin to top pin ...................18”
Height from bottom hitch pin to top pin....................... 19”
Lower pin diameter................................................. 7/8”
Lower pin diameter.................................................... 7/8”
Upper pin diameter................................................. 3/4”
Upper pin diameter....................................................... 1”
Linch pin diameter..............................................15/32”
Linch pin diameter................................................. 15 32”
3.2 Tractor Safety Devices
If transporting or operating the tractor and implement near a public roadway, the tractor must be equipped with
proper warning lighting and a Slow Moving Vehicle (SMV) emblem which are clearly visible from the rear of
the unit. Lights and a SMV emblem must be equipped directly on implements if the visibility of the tractor
warning signals are obscured.
Maintain all manufacturer equipped safety shields and guards. Always replace shields and guards that were
removed for access to connect, service, or repair the tractor or implement. Never operate the tractor PTO
with the PTO master shield missing or in the raised position.
OPS-U- 0004
Содержание RTX85G
