manualshive.com logo in svg

Burnham K2WT Residential, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Burnham K2WT Residential Скачать руководство пользователя страница 63

63

107672-03 - 5/18

VII.  Venting 

I. Assembly of Stainless Steel Vent Systems

1. 

This boiler has been listed for use with Duravent FasNSeal Flex Stainless Steel vent systems to be provided 

by the installer.

2. 

The vent adaptor has three different inside diameters. The smaller, lower diameter accepts 3” Stainless steel 

(Figure 7.27). A locking band clamp in the adaptor prevents the vent pipe from coming out of the adaptor 

once it is installed and tightened. Lubricate the upper gaskets in the vent adaptor with water and insert the 

first piece of 3” stainless into the adaptor until it bottoms out. Tighten locking band clamp to secure vent 

pipe.

3. 

Installation of Air Intake System - Start assembly of the PVC air intake system at the boiler. Assembly of the 

air intake system is done in the same manner as the vent system except as follows:

 
a.  Drill a 7/32” clearance hole into the front side of the air intake adaptor. Insert the first piece of PVC air  

 

intake pipe into the air intake connection and drill a 1/8” tap hole into the PVC which lines up with the 7/32”  

clearance hole and secure them together with a #10 x 1” sheet metal screw. Seal the joint between the intake  

pipe and the adaptor with RTV.

b.  All intake piping may be PVC.
c.  There is a 0” minimum clearance between the air intake piping and all types of construction.
d.  To the extent possible, pitch horizontal air intake piping towards the outside.

4. 

Installation using DuraVent FasNSeal Flex  (Option 39) 

 

Refer to manufacturer’s instructions for assembly of all flex components including the chimney cap and 

adaptor to rigid pipe at base of masonry chimney. In addition, observe the following requirements:

 

      a.  Refer to the appropriate Vent option in table 7.21 for a list of the principle flex components required. Rigid   

vent pipe by the same manufacturer will also be required for the run from the boiler to the base of chimney.

      b.  Masonry chimneys cannot be used for an air chase.

 

 

           Asphyxiation Hazard.  Follow these instructions and the installation instructions 

included by the original stainless steel venting component manufacturer DuraVent. Failure to do so 
could cause products of combustion to enter the building, resulting in severe property damage, personal 
injury or death. Where a conflict arises between DuraVent or instruction and these instructions, the more 
restrictive  instructions shall govern.
Do not mix vent components from listed manufacturers.
Examine all components from listed manufacturers.
All all components from listed manufacturers.

 

 

         Asphyxiation Hazard.  Vent systems made by Duravent rely on gaskets for proper sealing. 

When these vents systems are used, take the following precautions:

•

 Make sure that gasket is in position and undamaged in the female end of the pipe

•

 Make sure that both male and female pipes are free of damage prior to assembly.

•

 Only cut vent pipe as permitted by the vent manufacturer in accordance with their instructions

When pipe is cut, the cut end must be square and carefully de-burred prior to assembly.

NOTICE

 The venting system must be free to expand and contract and supported in accordance with the 

installation instructions included by the original stainless steel venting component manufacturer.

 

 

WARNING

 

 

WARNING

I.  Assembly of Stainless Steel Vent Systems

Содержание K2WT Residential









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды