Burnham K2WT Residential Скачать руководство пользователя страница 141

Страница: 141 / 168

141

107672-03 - 5/18

Indication

Condition

Possible Cause

Zone Panel

Setup

Flashing

Zone Panel 1

Setup

Flashing

Zone Panel 1 communication lost, typical for Panel 1 through 4: The zone panel’s

communication was established and then lost. Check the following to correct the

issue:

• Wiring between panel and boiler.

• Zone panel DIP switch settings have changed:

- Set Master/Slave switch to “Master”

- Set Zone Control switch ZC1 to “ON”

- Cycle power

Zone Panel Electronics Failure: A Zone Panel

Duplicate Zone: The Control has detected duplicate zone panel numbers. Check

the following to correct:

• Each Zone Control DIP Switch must be set to a Unique setting:

Note that when multiple ZC switches are set on ON the Zone Panel is
reported as Zone Panel 1.

Sequencer

Setup

Sequencer

Setup

Fault

This alarm is active if the slave boiler has lost communication with the Sequence

Master. Check the following:

- RJ 45 peer-to-peer network disconnected

- Sequencer Master was Enabled and then Disabled

- Master’s Boiler has been powered down.

- To clear fault restore communication or cycle power

Boiler Size

Setup

Boiler

Size

Fault

WARNING!

Boiler size setting may not match actual boiler size.

The Boiler size setting determines min, max and light-off blower speeds. Incorrect

boiler size can cause hazardous burner conditions and improper operation that may

result in PROPERTY LOSS, PHYSICAL INJURY, OR DEATH.

Refer to page 117 for boiler size setting instructions.

XIV. Troubleshooting

(continued)

C. Help Screen Faults

Zone Panel

Failure

Flashing

Duplicate

Zone

Flashing

D. Help Screen Diagnostic Features

Indication

Possible Cause

Lockout History is stored in a first-in, first-out basis. Each History file is stored with boiler run hour of when the

lockout occurred.

The “When happened” and “Current” provide:

- “Current” is the run hour and status the boiler just finished.

- “When happened” is the run hour and status when the lockout occurred.

For Service Contact:

CONTRACTOR NAME

CONTRACTOR ADDRESS 1

CONTRACTOR ADDRESS 2

PHONE NUMBER

The user is given the contact information of the responsible service provider. Refer to page 124 for data entry

instructions.

Содержание K2WT Residential









































































































































































Результаты поиска

Содержание K2WT Residential

Отзывы:

Бренды по названию

Популярные бренды

Burnham K2WT Residential, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание K2WT Residential

Отзывы:

Бренды по названию

Популярные бренды