manualshive.com logo in svg

Burnham K2WT Residential, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Burnham K2WT Residential Скачать руководство пользователя страница 46

46

107672-03 - 5/18

VII.  Venting 

E. Assembly of CPVC/PVC Vent Systems (continued)

5.  Installation of IPEX low profile vent terminal (Terminal Option B) - See Figure 7.30:

a.  Cut two holes in wall to accommodate the size PVC pipe being used.  The distance between hole centers is 

5.6”.

b.  Slide both vent and intake air pipes through the holes, and cement them to the base of the vent termination kit 

using a primer and cement listed for use with PVC.

c.  Fasten the vent base to the wall using the supplied screws and anchors.  The anchors require the drilling of a 

3/16” hole x 1-3/16” deep.  Locate the holes using the vent base as a template.

d.  Screw the vent cap to the vent base using the supplied screws.
e.  Once the vent termination and pipes are secure seal the wall penetrations from the interior using a weather 

resistant RTV sealant.

6.  Installation of DiversiTech Low Profile Terminal (Terminal Option C) – See Figure 7.31:

a.  Use vent plate as a guide to locate the openings for the vent and air intake pipes, as well as to locate the 

holes for the mounting screws. 

b.  Drill two 3-1/8 holes through the wall for the vent and intake pipes.
c.  Drill four 3/16 holes for the mounting screws.
d.  Install the vent and intake pipe sections passing through the wall. Cut the pipes so that they protrude the 

following distances from the surface on which the vent plate will be mounted:

•  Vent: Between 1-3/4 and 2-1/4”
•  Intake: Between ¼ and 1”

e.  Seal pipe penetrations in wall with RTV (silicone sealant).
f.  Mount the vent plate using the #8 x 2” screws and anchors provided with this kit.
g.  Seal the vent plate to the wall with RTV.
h.  Apply a bead of RTV around the OD of the vent pipe near its end.
i.  Slide the vent cap over the vent pipe and secure to the wall plate with the #8 x 2” screws provided.

7.  Installation of  IPEX  FGV or DiversiTech CVENT Concentric Vent Terminal (Terminal Options D,E,I & J) - This 

terminal may be used for either horizontal or vertical venting.  See Figure 7.33 for horizontal installation or Figure 

7.34 for vertical installation.  When PVC is used for venting, a 30” CPVC straight section and CPVC elbow must 

be used prior to connection of the vent system to this terminal. If the vent system is too short to permit this, use 

the IPEX FGV CPVC terminal:

a.  For horizontal installations at the planned location cut a round hole in the exterior wall 1/2” larger than the “C’ 

dimension indicated on Figure 7.32 for the size terminal being used. (See Section VII - B of this manual for 

permitted terminal locations).

b.  For vertical installations, cut a hole in the roof large enough to clear the concentric terminal at the location of 

the terminal (see Section VII - C of this manual for permitted terminal locations).

c.  If desired, the terminal can be shortened. See Figure 7.32 for specific information on making the terminal kit 

shorter based on the kit size being used. Cut the pipe squarely and de-burr both the OD and ID of the cut 

edges.

d.  Cement the inner pipe section of PVC pipe supplied with this kit to the Wye fitting using a primer and cement 

listed for use with PVC.

e.  Cement the outer pipe to the Wye, being careful, to keep the inner and outer pipes concentric.

 

 

            Asphyxiation Hazard.  CPVC/PVC vent piping and fittings rely on glued joints for proper 

sealing.  Follow all manufacturer instructions and warnings when preparing pipe ends for joining and 
using the primer and the cement.
When PVC is used with the concentric vent kit, a 30” CPVC straight section and elbow must be used prior 
to connection of the vent system to this terminal. If the vent system is too short to permit this, use an FGV 
CPVC terminal.
Do not operate boiler without the rain cap in place. 
Method of securing and sealing terminals to the outside wall  must not restrain the expansion of vent 
pipe. 

 

 

WARNING

•

•

•

Содержание K2WT Residential









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды