Burnham FREEDOM FCM120 страница 62 Скачать руководство пользователя

Страница: 62 / 80

TABLE 14.4: HARD LOCKOUT CODES DISPLAYED

CODE

CONDITION

POSSIBLE CAUSES

E 00

ame signal was present when there should

be no

ame.

• Defective gas valve - make sure inlet pressure is below maximum on rating plate

before replacing valve.

E 02

Flame failure after 5 tries to restart

• No gas pressure
• Gas pressure under minimum value shown on rating plate
• Gas line not completely purged of air
• Defective Electrode
• Loose burner ground connection
• Defective Ignition Cable
• Defective gas valve (check for 24 VDC at harness during trial for ignition before

replacing valve)

• Air-fuel mixture out of adjustment - consult factory

E 03

Gas valve error

• Loose or defective gas valve harness. Check electrical connections.
• Defective gas valve (check for 24 VDC at harness during trial for ignition before

replacing valve)

E 04

Power failure occurred after lockout

• Some other error on this list occurred and power to the boiler was then

interrupted. Reset control and see if hard lockout reoccurs.

E 05
E 06
E 07

E 11

Internal control failure

• Reset the control. If problem reoccurs, replace the MCBA.

E 12

Low water cut-off circuit open

• If yellow light on LWCO is on, system is low on water
• If neither yellow nor green light is on, check LWCO harness and check for

24VAC across AT140 transformer

E 13
E 14
E 15
E 16
E 17

Internal control failure

• Reset the control. If problem reoccurs, replace the MCBA.

E 18

MCBA supply sensor detected temperatures in
excess of 200°F for an extended period of time

• See possible causes for “b18” error. Also, check safety limit for proper operation.

E 19

MCBA return sensor detected temperatures in
excess of 200°F for an extended period of time

• See possible causes for “b19” error.

E 28

Blower is not running when it should or fan speed
signal not being detected by MCBA

• Loose connection in 120 VAC fan wiring
• Loose or miswired fan speed harness
• Defective fan

E 29

Blower fan speed has not returned to zero rpm

• Miswired fan speed harness
• Defective fan

E 31

Shorted supply temperature sensor

• Shorted or miswired supply sensor wiring
• Defective supply sensor

E 32

Shorted return temperature sensor

• Shorted or miswired return sensor wiring
• Defective return sensor

E 35

Flue gas temperature sensor short circuit

• Shorted or miswired

ue temp sensor wiring

• Defective

ue temp sensor

E 36

Supply water temperature sensor circuit open

• Loose or miswired supply sensor wiring
• Defective supply sensor

E 37

Return water temperature sensor circuit open

• Loose or miswired return sensor wiring
• Defective return sensor

E 40

Flue gas temperature sensor circuit open

• Loose or miswired

ue temp sensor wiring

• Defective

ue temp sensor

E 44

Internal control failure

• Reset the control. If problem reoccurs, replace the MCBA.

E 52

Flue gas temperature over 230°F

• Heat exchanger needs to be cleaned
• Boiler over-

red

• Air-fuel mixture out of adjustment - consult factory

E 60

Internal control failure

• Reset the control. If problem reoccurs, replace the MCBA.

C. Trouble shooting problems where a hard lockout code is displayed. When a hard lockout occurs, the boiler

will shut down and the display will

ash the letter “E” followed by a two digit service code. Once the condition

that caused the lockout is corrected, the boiler will need to be manually reset using the RESET button on the

display.

Содержание FREEDOM FCM120

















































































Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды

Burnham FREEDOM FCM120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды