Burnham FREEDOM FCM120 страница 50 Скачать руководство пользователя

Страница: 50 / 80

10) Check the inlet pressure and adjust if necessary. Verify that the inlet pressure is between the upper and lower limits shown

on the rating plate with all gas appliances on and off.

WARNING

THE OUTLET PRESSURE FOR THE GAS VALVE HAS BEEN FACTORY SET

AND REQUIRES NO FIELD ADJUSTMENT. THIS SETTING IS SATISFACTORY

FOR BOTH NATURAL GAS AND PROPANE. ATTEMPTING TO ADJUST THE

OUTLET PRESSURE MAY RESULT IN DAMAGE TO THE GAS VALVE AND

CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

7) Start the boiler using the lighting instructions on page 49. After the boiler is powered up, it should go through the following

sequence.

Sequence Display

Meaning

U.125

or Blank

Checking internal software (power-up only)

0.SWT

Boiler in standby.

SWT

= Supply Water Temp. No call for heat.

(After call for heat from heating thermostat)

A.SWT

Self-Check on Start-up

5.SWT

Blower and circulator on. Checking for adequate air

ow.

1.SWT

Prepurge

2.SWT

Trial for ignition

3.SWT

Flame established. Boiler responding to a call for heat.

8) Upon initial start-up, the gas train will be

lled with air. Even if the gas line has been completely purged of air, it may take

several tries for ignition before a

ame is established. If more than 5 tries for ignition are needed, it will be necessary to

press the reset button to restart the boiler. Once a

ame has been established for the

rst time, subsequent calls for burner

operation should result in a

ame on the

rst try.

9) Inspect

the

ame visible through the window. On high

re the

ame should be stable and mostly blue (Fig.11.1). No yellow

tipping should be present; however, intermittent

ecks of yellow and orange in the

ame are normal.

Figure 11.1: Burner Flame

Содержание FREEDOM FCM120

















































































Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды

Burnham FREEDOM FCM120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды