Burnham FREEDOM FCM120 страница 77 Скачать руководство пользователя

Страница: 77 / 80

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When

the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide
the parts for venting the

ue gases, but identi

es “special venting systems”, the following requirements shall be

satis

ed by the manufacturer:

1. The referenced “special venting system” instructions shall be included with the appliance or equipment

installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system

shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions
shall remain with the appliance or equipment at the completion of the installation.

Содержание FREEDOM FCM120

















































































Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды

Burnham FREEDOM FCM120, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FREEDOM FCM120

Отзывы:

Похожие инструкции для FREEDOM FCM120

Бренды по названию

Популярные бренды