manualshive.com logo in svg

Burnham CHG CHG150, Руководство по установке и эксплуатации

"Установочно-эксплуатационное руководство для продукта Burnham CHG CHG150 доступно для скачивания бесплатно на нашем сайте. Это важное руководство содержит всю необходимую информацию о правильной установке и эксплуатации продукта. Скачайте его сейчас с manualshive.com и ознакомьтесь с особенностями этого продукта."

Поделиться
Скачать
background image

15

B. Removing an Existing Boiler From a Common Chimney

 

Read this only if the CHG boiler is replacing an existing boiler that is being removed from a common chimney.   

This section does not apply to the installation of a CHG boiler. 

 

In some cases, when an existing boiler is removed from a common chimney, the common venting system may    

be too large for the remaining appliances. At the time of removal of an existing boiler, the following steps shall be  

followed with each appliance remaining connected to the common venting system placed in operation, while the  

other appliances remaining connected to the common venting system are not in operation.
(a)  Seal any unused openings in the common venting system.
(b)  Visually inspect the venting system for proper size and horizontal pitch and determine there is no    

 

blockage or restriction, leakage, corrosion and other deficiencies which could cause an unsafe condition.

(c)  Insofar as practical, close all building doors and windows and all doors between the space in which all the 

appliances remaining connected to the common venting system are located and other spaces of the building.  

Turn on clothes dryers and any appliance not connected to the common venting system. Turn on any exhaust 

fans, such as range hoods and bathroom exhausts, so they will operate at maximum speed. Do not operate a 

summer exhaust fan. Close fireplace dampers.

(d)  Place in operation the appliance being inspected. Follow the lighting instructions. Adjust thermostat so the    

appliance will operate continuously. 

(e)  Test for spillage at the draft hood relief opening after 5 minutes of main burner operation. Use the flame of    

a match or candle, or smoke from a cigarette, cigar, or pipe.

(f)  After it has been determined that each appliance remaining connected to the common venting system  

 

properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace dampers and    

any other gas-burning appliances to their previous condition of use.

(g)  Any improper operation of the common venting system should be corrected so the installation conforms  

 

with the National Fuel Gas Code, ANSI Z223.1. When re-sizing any portion of the common venting  

system, the common venting system should be re sized to approach the minimum size as determined using    

the appropriate tables in Part 11 of the National Fuel Gas Code, ANSI Z223.1.

warNINg

NEVEr COmmON VENT a Chg bOIlEr wITh OThEr aPPlIaNCEs

CauTION

VENT SySTEMS MADE By BuRNHAM, HEAT FAB, PRoTECH, AND Z-FLEx RELy oN GASkETS 

FoR PRoPER SEALING. WHEN THESE VENT SySTEMS ARE uSED, TAkE THE FoLLoWING 

PRECAuTIoNS:
•   MAkE SuRE THAT GASkET IS IN PoSITIoN AND uNDAMAGED IN THE FEMALE END oF THE  

  PIPE.

•   MAkE SuRE THAT BoTH THE MALE AND FEMALE PIPES ARE FREE oF DAMAGE PRIoR To  

  assEmbly.

C. Vent / Intake System Assembly 

1)  General Assembly Notes:

a)   Where the use of “silicone” is called for in the following instructions, use GE RTV 106 for the vent collar.   Air 

inlet piping sections are sealed with any general-purpose silicone sealant such as  GE RTV102. PVC air  

 

inlet piping sections are connected with PVC cement. 

b)   Longitudinal welded seams should not be placed at the bottom of horizontal sections of exhaust pipe.
c)   Do not drill holes in vent pipe. 
d)   Do not attempt to mix vent components of different vent system manufacturers.
e)   In some cases, there are differences between the vent system installation instructions in this manual and 

those in the vent system manufacturer’s manual. Where such differences exist, this manual takes    

 

precedence over the vent system manufacturer’s manual.

Содержание CHG CHG150









































































Отзывы:

Нет отзывов

Похожие инструкции для CHG CHG150

Daikin Altherma 3 H F User Reference Manual preview
Altherma 3 H F
Бренд: Daikin Страницы: 24
NTI Trinity TX101 Installation And Operation Instructions Manual preview
Trinity TX101
Бренд: NTI Страницы: 84
IBC Technologies SL 20-115 Installation And Operating Instructions Manual preview
SL 20-115
Бренд: IBC Technologies Страницы: 80
MHG Heating ProCon E 26 Installation And Operating Manual preview
ProCon E 26
Бренд: MHG Heating Страницы: 73
Ferroli ARENA 30 A Installation And Operating Instructions Manual preview
ARENA 30 A
Бренд: Ferroli Страницы: 44
Clifton Range 1000 Series User Manual preview
1000 Series
Бренд: Clifton Range Страницы: 10
Bongioanni Multidea Evo 100 Installation And Maintenance Instructions Manual preview
Multidea Evo 100
Бренд: Bongioanni Страницы: 64
Baxi Roca LIDIA 20 GT EM Operating, Cleaning And Maintenance Instructions For The User preview
Roca LIDIA 20 GT EM
Бренд: Baxi Страницы: 3
Baxi PRIME HT 1.120 Installers And Users Instructions preview
PRIME HT 1.120
Бренд: Baxi Страницы: 40
Baxi Nuvola 3 BS 140 Fi Operating And Installation Instructions preview
Nuvola 3 BS 140 Fi
Бренд: Baxi Страницы: 224
Thermo Dynamics VTF Series Installation, Operation & Maintenance Manual preview
VTF Series
Бренд: Thermo Dynamics Страницы: 23
Rinnai E32S Installation & Servicing Instructions Manual preview
E32S
Бренд: Rinnai Страницы: 40
Potterton Paramount five 115 Installation Manual preview
Paramount five 115
Бренд: Potterton Страницы: 156
E-COMPACT 15 Installation & Operation Manual preview
15
Бренд: E-COMPACT Страницы: 38
Truma Boiler Elektro BE14 Operating Instructions Manual preview
Boiler Elektro BE14
Бренд: Truma Страницы: 6
Baxi Boston 2 40 OF Installation And Servicing Instructions preview
Boston 2 40 OF
Бренд: Baxi Страницы: 14
Baxi Bioflo 12 kW Pear User Operating Instructions Manual preview
Bioflo 12 kW Pear
Бренд: Baxi Страницы: 60
Ideal Boilers Classic FF 330 Installation And Servicing preview
Classic FF 330
Бренд: Ideal Boilers Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды