background image

Instructions

Models GBVS 39/44/49

 

Equipped with 

*

Safety Pilot System

Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do 

not use any phone in your building.

Immediately call your gas supplier from 

a neighbor’s phone and follow the gas 

supplier’s instructions.

If you cannot reach your gas supplier, 

call the fire department.

Installation and service must be 

performed by a qualified installer, service 

agency, or the gas supplier.

WARNING:

If the information in these instructions is 

not followed exactly, a fire or explosion 

may  result  causing  property  damage, 

personal injury or death.

rev  5-31-2013

Gas Fireplace with Masonry Firebox

L

ogs and burner must be permanently installed in and 

are  only  for  use  in  this  fireplace. This  fireplace  must 

be connected to a working flue meeting the 

requirements of the ANSI Z21.50 standard.

Solid-fuels shall not be burned in this fireplace.

This  appliance  must  be  vented  vertically  through  the 

roof. This appliance is not for installation in manufactured 

or  mobile  homes.  The  installation,  including  provisions 

for  combustion,  ventilation  air,  and  required  minimum 

permanent vent opening, must conform with the National 

Fuel  Gas  Code  (ANSI  Z223.1/NFPA 54)  and  applicable 

local building codes. 

This gas fireplace is designed to 

burn with yellow flames; thus adequate ventilation is 

absolutely necessary.

IMPORTANT:

 READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THIS FIREPLACE. 

WARNING:

This gas appliance must not be connected to a chimney 

fuel servicing a solid fuel burning appliance.

Do not store gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Report N

o.

08-154

ICC Evaluation Services 

Report No. 2401

This appliance is only for use with the type 

of gas indicated on the rating plate. This 

appliance is not convertible for use with 

other gases, unless a certified kit is used.

Installer:

 Leave these instructions with the consumer.

Consumer:

 Retain for future reference.

WWW.BURNTECH.COM

*Sold Seperately

Содержание GBVS 39/44/49




























Отзывы: