background image

 

- 13 - 

USE ONLY GENUINE REPLACEMENT PARTS. 

User Instructions 

 

GENERAL REQUIREMENTS 

The heater is intended as a secondary heat source. Check that a primary source of heat (such as 
radiators) is present in the room. If insufficient primary heat is being used there may be a build up 
of condensation. 

The heater must not be used on or against a combustible surface. No furniture or curtains must be 
close to the appliance (or at risk of being blown close). 

In the event of a gas leakage from the appliance, the gas supply must be turned off at the nearest 
isolating valve. 

The  area  in  which  the  fire  is  installed  must  have  at  least  100cm²  of  ventilation.  (For  Republic  of 
Ireland 2 openings at high and low level, each of 60cm², with a vertical separation of at least 1.6 
metres) 

The heater must not be used in a room area of less than 30m³. Adjoining spaces, not separated by 
a door may be included. To convert cubic feet (ft³) to cubic metre (m³) divide the room volume in 
cubic feet by 35.3. 

The heater must  not  be  installed in high rise  blocks of flats,  bed sitting rooms, basements which 
are  not  open  on  at  least  one  side,  bathrooms,  bedrooms,  in  corridors  stairways  landings  or 
hallways of multi occupancy dwellings, in garages or rooms containing petroleum products. 

The guard on the appliance is to prevent risk of fire or injury from burns and no part of it may be 
permanently  removed.  It  does  not  give  full  protection  for  young  children,  the  elderly  or  infirm. 
Parts of the appliance get hot; it is strongly recommended that an additional guard to BS6539 or 
BS6778 is used in the presence of children, the elderly or infirm. 

This is not a drying appliance. Do not place clothing or other articles, on or against it. 

Do not store or use flammable substances on or near the heater. 

Do not spray aerosols on or near the heater. 

If any material, such as plastic, melts onto the surface of the glass, turn the heater 

off

 and 

allow it 

to cool. Do not remove the material when hot.

  

When  the  heater  is  not  to  be  used  for  a  time,  ensure  the  gas  control  or  adjacent  isolator  are 
turned off. 

The heater must not be used in rooms where the atmosphere is likely to contain water or chemical 
vapours, which may adversely affect the appliance or its finish.

 

 

Do not use whilst painting & decorating, or in newly decorated rooms as the residues can lead to 
unpleasant  smells  from  the  appliance.  Always  cover  or  have  the  appliance  removed  when 
decorating. 

Содержание G4237 IMAGE





















Отзывы: