Bunn CDS-2 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 60

background image

38

R22

FIG. 29 ELECTRONIC CONTROL

Location:

The electronic control is located on the outside of

the component bracket inside the chassis on the right
side.

Test Procedure:
1. Disconnect the dispenser from the power source.
2. Disconnect the plug from the main harness from

the connector on the electronic control.

3. With a voltmeter, check the voltage across the

socket #23 and socket #24 in the plug from the
main harness and “ON/OFF” switch in the “ON”
position. Connect the dispenser to the power
source. The indication must be:
a) 120 volts ac for 120 volt models.
b) 230 volts ac for 230 volt models.

4. Disconnect the dispenser from the power source.
If voltage is present as described, replace the elec-
tronic control.
If voltage is not present as described, refer to the
Wiring Diagram and check the dispenser wiring har-
ness.

P1342

SERVICE (cont.)

ELECTRONIC CONTROL

Removal and Replacement:
1. Disconnect the plug from the main harness from

the connector on the electronic control.

2. Remove the two #8-32 locking screws securing

electronic control to the component bracket. Re-
move and discard the electronic control.

3. Install new electronic control using two #8-32

locking screws.

4. Reconnect the plug from main harness to the

connector on the electronic control.

27646 122200

«
...
36
37
38
39
40
...
»

Содержание CDS-2





























































Отзывы:

Нет отзывов

Похожие инструкции для CDS-2

Бренд: Hamilton Beach Страницы: 8

SmartServe BIC2000

Бренд: Hamilton Beach Commercial Страницы: 28

Type I CHILL-003

Бренд: BRAVILOR BONAMAT Страницы: 16

Бренд: Talent Страницы: 28

Tough Guy 40CA23

Бренд: Grainger International Страницы: 9

Бренд: Wunder-Bar Страницы: 26

Бренд: blupura Страницы: 36

Бренд: blupura Страницы: 36

Бренд: Coffee Queen Страницы: 17

Бренд: KENT Страницы: 4

Бренд: MOA Страницы: 40

PROFESSIONAL AQUARIUS 6994

Бренд: Kimberly-Clark Страницы: 9

Бренд: Maxima Страницы: 12

Бренд: Bunn Страницы: 6

Бренд: Wagner Ewar Страницы: 30

Бренд: VALCO MELTON Страницы: 123

Бренд: AFWFilters Страницы: 28

EFHA14 1H Series

Бренд: Elkay Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды