manualshive.com logo in svg

Bunn CDS-2, Руководство по эксплуатации и обслуживанию

Bunn CDS-2 - Профессиональная кофейная машина, предназначенная для коммерческих целей. Чтобы использовать ее на полную мощность, вам понадобится Операционно-служебный руководство. Вы можете скачать его бесплатно с manualshive.com, чтобы научиться правильно эксплуатировать свою кафемашину.

Поделиться
Скачать
background image

21

Auger Motors .................................................................................................. 22
Auger Motor Capacitors ................................................................................... 23
Auger Shaft Assembly ..................................................................................... 24
Auger ON/OFF Switches ................................................................................... 26
Circuit Breaker ................................................................................................. 27
Compressor (CDS-2) ....................................................................................... 28

  (Compressor, Compressor Start Capacitor, Compressor Start Relay, Thermal Overload Protector)

Compressor (CDS-3) ....................................................................................... 31

  (Compressor, Compressor Start Capacitor, Compressor Start Relay, Thermal Overload Protector)

Contactor ......................................................................................................... 34
Cooling Drum Alignment ................................................................................. 35
Day/Night Switch ............................................................................................. 36
Dispenser ON/OFF Switch ................................................................................ 37
Electronic Control ............................................................................................ 38
Fan ................................................................................................................... 39
Fuse and Fuse Holder ...................................................................................... 40
ICE/OFF/NO ICE Switch .................................................................................... 41
Lamp Cord Assembly ...................................................................................... 42
Lamp Cord Connector...................................................................................... 43
Lamp Holder/Socket Assembly ........................................................................ 44
L.E.D./Adjustment Board ................................................................................. 45
Solenoids ......................................................................................................... 46
Temperature Sensor Assembly ........................................................................ 47
Torque Sensor Circuit Board ............................................................................ 48
Transformer ..................................................................................................... 49
Voltage Divider ................................................................................................ 50
Coolant Schematics ......................................................................................... 51
Electrical Schematics ....................................................................................... 54

SERVICE

This section provides procedures for testing and replacing various major components used in this dispenser

should service become necessary. Refer to 

Troubleshooting for assistance in determining the cause of any

problem.

WARNING

- Inspection, testing, and repair of electrical equipment should be performed only by qualified service

personnel. The dispenser should be disconnected from the power source when servicing, except when electrical
tests are required and the test procedure specifically states to connect the dispenser to the power source.

COMPONENT ACCESS

WARNING

 - Disconnect the dispenser from the power source before the removal of any panel or the replacement

of any component.

All components are accessible by removal of the auger motor cover, lower drip tray, front cover and the left and

right side covers.

Refer to the contents listing for component location.

Contents

27646 122200

Содержание CDS-2





























































Отзывы:

Нет отзывов

Похожие инструкции для CDS-2

Canature 95 Series Installation And Operation Manual preview
95 Series
Бренд: Canature Страницы: 28
WaterCare CS-5 Installation Instructions Manual preview
CS-5
Бренд: WaterCare Страницы: 7
ScaleBlaster SB-175 Installation & Operation Manual preview
SB-175
Бренд: ScaleBlaster Страницы: 8
Fancom FaroTek Installation Manual preview
FaroTek
Бренд: Fancom Страницы: 37
Hidro-Water KOBE WS1CI UF User& Installer'S Manual preview
KOBE WS1CI UF
Бренд: Hidro-Water Страницы: 19
KitchenAid Instant-Hot KHWC260 Installation And User Instructions Manual preview
Instant-Hot KHWC260
Бренд: KitchenAid Страницы: 24
KitchenAid Instant-Hot KHWS160 Use And Care Manual preview
Instant-Hot KHWS160
Бренд: KitchenAid Страницы: 6
KitchenAid INSTANT-HOT KHLC260 Installation & User'S Instructions preview
INSTANT-HOT KHLC260
Бренд: KitchenAid Страницы: 24
KitchenAid KHWC160 Series Installation Instructions And Use And Care Manual preview
KHWC160 Series
Бренд: KitchenAid Страницы: 20
Stoelting O231 Service Manual preview
O231
Бренд: Stoelting Страницы: 63
GMCW Crathco G-Cool C-1S-16 Operator'S Manual preview
Crathco G-Cool C-1S-16
Бренд: GMCW Страницы: 20
physa PHY-DDS02 User Manual preview
PHY-DDS02
Бренд: physa Страницы: 5
Rieber ERR User Manual preview
ERR
Бренд: Rieber Страницы: 32
Chocolate World M1088 Operator'S Manual preview
M1088
Бренд: Chocolate World Страницы: 9
Arktic 425206 User Manual preview
425206
Бренд: Arktic Страницы: 100
Glacial 8LDIECH-SC-WFC-SSF User Manual preview
8LDIECH-SC-WFC-SSF
Бренд: Glacial Страницы: 18
UBC Cool KegMaster-2 Owner'S Manual preview
KegMaster-2
Бренд: UBC Cool Страницы: 12
Perlick Keg Couplers Tapping Equipment Datasheet preview
Keg Couplers Tapping Equipment
Бренд: Perlick Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды