background image

SYSTEM FEATURES

SYSTEM COMPONENTS

1

Your system includes:

1-Installation & Operation Guide

1-Main Control Module

2-Four Button Remote Transmitter with Slide Protectors

1-(4) Relay Harness with Relays

1-18-Pin Wire Harness

REQUIRED TOOLS

1-5 Pin Harness (door locks)

1-Hood Pin Switch

1-Extended Range Antenna with L.E.D.

1-Warranty

1-Warning Sticker for Under the Hood

2-Bulldog Window Decals

A 5/16 inch drill bit is needed when mounting the hood pin switch. You will also need a sharp knife,

electrical tape and a computer-friendly test light. If the bottom of your dash on the driver’s side will

come off, you must remove it. If this is the case a screwdriver or a socket set may be needed,

2 Four-Button Extended Range

Remotely start your car to run the heater or air conditioning from an extended distance.

Remote Control

Keyless Entry

Remotely locks and unlocks your power door locks with built-in relays onboard.

Built In Alarm Features

Provides door, hood and impact protection.

Onboard Dual Stage Shock Sensor

Provides warn away protection and impact protection.

Door Trigger Protection 

Provides protection when doors are opened.

Ignition Controlled Door Locks

A programmable feature that locks and unlocks the doors when the brake is depressed or the

ignition is cycled.

Trunk Release

Remotely opens your trunk with a push of a button.

Extended Range Antenna

Allows you to operate your system from up to a quarter mile away.

Diesel Start Application

Remote starter section works on all diesel engines.

Double Crank Time

Provides longer engine cranking for hard starting diesel vehicles.

Low Voltage Start

Automatically starts your vehicle when battery voltage drops below 11 volts.

Automatic Hot and Cold Start

Remotely program your car to start at a preset temperature. Automatically starts your car in

extreme temperatures.

Automatic Start

Remotely program your car to start every 3 hours regardless of temperature.

Dome Light Supervision

Never walk up to a dark vehicle again. When unlocking the vehicle by remote control the dome

light will come on and stay on for 1 minute, or until you activates the ignition switch.

Remote Programmable Run Time

Remotely program your vehicle to run 5 to 25 minutes.

Parking Light Confirmation

Confirms that your vehicle has received a remote signal and will remain on if the engine is

remotely started.

Horn and Siren Output

Lets you choose between the vehicle’s factory horn or an optional six tone siren.

Remote Car Finder

Lets you locate you vehicle in a crowded parking lot.

Remote Valet

Lets you program off the alarm section when it is not needed.

Tach/Tachless Option

A programmable feature that lets you choose from the easy to install tachless operation or

the standard wire-in, tach operation.

Pit Stop Mode

Allows you to exit the vehicle while the engine remains running.

Code Learning

Allows your remote starter to learn new remotes, should you want to add remotes, or if remotes

are lost.

Starter Immobilizer

When the alarm is armed, this option breaks the starter wire in half so the vehicle cannot be

hotwired.

Limited Lifetime Warranty

Guarantees life-long protection.

Содержание DELUXE 12














Отзывы: