background image

HEATER/BLOWER MOTOR WIRE(S) (+12V in run position only)

Most vehicles will have (1) blower wire; however some Fords, newer GM vehicles and Chrysler 94 and up

will have (2) or more blower wires. To locate these wire(s) probe for wire(s) that only show +12V when

the ignition switch is in the RUN position only. This wire(s) will not show +12V when the ignition switch

is in any other position.

1.If your vehicle has only (1) blower wire connect the WHITE WITH BLACK STRIPE wire from the 4-relay

harness to this wire.

2.If your vehicle has (2) blower wires, connect the WHITE WITH BLACK STRIPE wire to both.

3.If your vehicle has (3) blower wires connect the unused WHITE wire from the 4-relay harness to the

third blower wire.

STARTER/CRANK WIRE (+12V only in the start position only)

The starter/crank wire is also in the main harness. Locate the wire that shows +12V only in the crank

position. This wire will not show +12V in any other position. Attach the YELLOW WITH BLACK STRIPE wire

from the 4-relay harness to this wire.

5

Note: Remove any paint below

the spade connector.

Factory Bolt

Spade Connector

Black Ground Wire

BRAKE INPUT

The brake wire is located on the switch near and above the brake pedal. The correct wire will show

+12V only when the brake is pressed. Connect the BLUE WITH BLACK STRIPE from the 18-pin harness to this

wire.

PARKING LIGHTS (+12V only with parking lights on)

Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS).

Probe the wire(s) coming from your headlamp control switch. Find

a wire that will show +12V only when the parking lights are ON.

Connect the BROWN wire from the 18-pin harness to this wire. If

this wire tests as a (-) negative, see diagram.

DO NOT USE THE RED WIRE, TAPE OFF.

87a

To (-)Parking

Light Output

To Ground

Brown wire

from 18 pin

harness

To Ground

YELLOW

BLACK

WHITE

BLUE

RED

Optional part #775 required.

NEGATIVE PARKING LIGHT OUTPUT

FACTORY ALARM SHUT DOWN WIRE (FASD) (-)

If your vehicle is equipped with a factory alarm system (as most vehicles with a factory keyless entry

are) probe for a small gauge wire (usually found in the driver’s side kick panel) that shows (-) ground

when the door lock cylinder is turned to the unlock position using the key. This wire will usually show

a (+) positive voltage before turning the key. NOTE: Some factory disarm wires remain neutral before

you turn the key to unlock instead of +12v positive. Connect the RED WITH BLACK STRIPE wire from the

18-pin harness to this wire.

CHASSIS GROUND

Locate an easy to get to bolt or screw

located under the driver’s side of the dash and

attach the BLACK ground wire from the 18-pin

harness securely as pictured.

DIESEL INSTALLATION ONLY

Connecting the Glow Plug or Wait to Start Wire

When installing on a diesel engine, a wire that energizes the Glow Plug (also known as the Wait to Start

Wire), must be located and identified. This wire is usually located at the instrument cluster or at the ECM

(electronic control module). This wire will, depending on the year, make and model of the vehicle, test as

a (+) positive or a (-) negative.

TO TEST FOR NEGATIVE: Clip the test light to ground, then probe the wire and turn the ignition key on. The

“Wait to Start Light” on the dash should be illuminated, the test light should also be illuminated. When the

“Wait to Start Light” on the dash goes out and the test light also goes out this is a (-) negative wire.

Connect the GREEN WITH THE BLACK STRIPE wire from the 18-pin harness to this wire.

TO TEST FOR POSITIVE: Clip the test light to ground, then probe the wire and turn the ignition key on. The

“Wait to Start Light” on the dash should be illuminated, the test light should not be illuminated. When the

“Wait to Start Light” on the dash goes out but the test light is illuminated this is a (+) positive wire.

Connect the BROWN WITH THE BLACK STRIPE wire from the 18-pin harness to this wire.

NOTE: You will need to program your unit for Diesel Start Mode. See programming on page 11.

Содержание DELUXE 12














Отзывы: