background image

2/10

CONTENTS

Technical data sheet:  S000092412EN-1 

Updated: 

Created: 02/06/2016

Cat No(s): LN4691KNX - H4691KNX

KNX temperature control panel

  1. USE

Combined with a KNX room temperature controller (with an embedded 

temperature control algorithm), the KNX temperature control panel is 

used to manage the heating/cooling control system (fan coil control 

unit, heating/cooling valve, electrical load, etc) in the rooms where it is 

installed, and can be configured for different applications as required. 

The temperature control panel incorporates a user interface and a 

temperature sensor.
This device is completely configurable in term of parameters, operating 

modes and other features. Depending on the type of use, the backlit 

display will show the following information: the current function or 

mode (Heating, Cooling; Comfort, Eco, Frost/Overheat Protection), the 

measured room temperature, the defined temperature setpoint, the 

fan coil speed. It is a native KNX device and all the configurations and 

associations must be made via ETS software (ETS versions 3, 4 and 5) 

only.

  2. DESCrIPTION

1 2

3 4 5

6

MODE

FAN

7

8

9

13

12

11 10

14

15

+

-

1 - Heating mode.
2 - Cooling mode.
3 - Comfort mode.
4 - Eco mode.
5 - Frost/Overheat protection.
6 -  MODE key: A short press changes the device operating mode;  

a long press changes the function.

7 - + key: increases the set value.
8 - – key: decreases the set value.
9 - FAN key: sets the fan-coil speed to one of 3 automatic.
10 - Heating On indicator.
11 - Cooling On indicator.
12 - Fan coil speed indicator, 3 levels.
13 - Fan coil in automatic mode indicator.
14 -  Measured temperature (thermometer symbol On)/set temperature 

(thermometer symbol Off) indicator.

15 - Unit of measurement: °C or °F.

  3. TEChNICal CharaCTErISTICS

3.1  Electrical characteristics

-  KNX BUS current consumption: 6 mA (OFF) / 9 mA (Backlight min ) /  

16 mA (Backlight max)

- KNX BUS power supply: 29 V =
-  KNX connector (red/black): terminal capacity 4x (Ø 0.6 to 0.8 mm) 

3.2  Climatic characteristics

- Environmental operating temperature: -0°C to +40°C
- Storage temperature: -25°C to +70°C

3.3  Mechanical characteristics

- Impact resistance: IK04
- Penetration by solid and liquid matter: IP20
-Weight: 40 g

LED

Prog and Reset

  4. DIMENSIONS

37

47

45

37

45

45

Содержание H4691KNX











Отзывы: