background image

BST Solutions GmbH  |  UV COMPACT FLAME DETECTOR IFC 10 

Page 10

Connection, set-up, maintenance and repair work may only be carried out by qualified spe-
cialist staff.
This device may cause hazards if it is operated inappropriately by untrained staff or if it is not 
used for its intended purpose.
Generally valid legal and other binding regulations on accident prevention and environmental 
protection in addition to basic health and safety requirements have to be observed. The ope-
rating company has to instruct its staff accordingly.

2.3   Safety instructions

The following instructions on accident prevention have to be observed when operating the 
compact flame detektor IFC 10.

2.4   Safety devices

2.4.1  Fundamental aspects
Check the safety equipment and locking devices on the device for safe operational condition.
Only operate the device if all safety devices are present and enabled. The operating company 
or operator of the compact flame detektor IFC 10 is responsible for the proper operation of 
the device.

The device has been fitted with warning and danger signs for the protection of operating 
staff. These signs have to be observed. Damaged or illegible signs have to be replaced 
immediately.

NOTICE

SAFETY

Only operate the device if it is in a proper state!
• Do not remove or disable safety devices.
•  Check for externally noticeable damage and defects prior to using the device! Immediately 

notify the appropriate authority/person of any changes that occur (including changes in 
operating performance). If necessary, stop and secure the device immediately.

•  Allow only authorised specialist staff to carry out set-up and/or maintenance work.
•  Replace worn or defective parts.
•  Use suitable maintenance tools only.
•  After repair work, refit all safety devices and carry out electrical and mechanical checks.
•  Check the operating instructions for details of displays as well as switch-on and 

switch-off procedures.

•  Prior to switching on the device, make sure that no-one can be endangered by the 

device!

•  The operating instructions always have to be kept close to the device and be readily 

at hand.

•  Any non-compliance with the safety instructions outlined in these operating instruc-

tions may lead to damage to property, personal injury or even death.

NOTICE

Содержание Flamonitec IFC Series

























Отзывы: