BSR BSR00034 Скачать руководство пользователя | Manualshive

Страница: 35 / 133

background image

INTRODUCTION

21

2

2.2.1 How

To

Setup/Configure the Scanner Network

A complete ID-NET™ scanner network can be rapidly setup, as follows:

Mounting & Connection

1. Mechanically mount/install all the readers (refer to par. 3.2 and 3.3).

2. Wire ID-NET™ (refer to par. 4.3 or 5.3).

3. Connect a PC equipped with Genius™ to the planned Master scanner.

4. Power up the entire system.

Configuration

1. Launch Genius™.

2. From the Genius™ Device Menu select “Local Device Network Settings” and program the

Role of the Master scanner (Synchronized or Multidata).

This procedure requires the Network Baud Rate be the same for all Slaves and Master,
(500 kbs is the default value). It can be changed after network setup using Genius™
through the Master scanner. See also the alternative procedure in the note below.

3. At the prompt to "Send updated Network configuration to the Local Device" (Master)

choose "Yes".

4. Then run the NET-AUTOSET procedure from the Icon in the Devices Area. Genius™

sets all slave scanners according to the Master Role (Synchronized or Multidata), and
assigns each a random address. If necessary, this address can be changed through the
Network Wizard.

5. Configure the System parameters via Genius™.

6. If using the CBX connection box equipped with a BM100 Backup module, perform

System Backup at the Master.

The scanner network is ready.

NOTE

If necessary, the ID-NET™ baudrate can be set individually on each Slave
scanner to match the Master. Connect each Slave to Genius™ and set the
Reading System Layout > Network Baudrate parameter. Then follow the
procedure above.

NOTE

An alternative method of programming scanner address and role
assignment can be accomplished by using the “Connectivity Programming
Barcodes” (refer to the “Setup Procedure Using Programming Barcodes”
document on the product CD).

«
...
33
34
35
36
37
...
»

Содержание BSR00034






































































































































Отзывы:

Нет отзывов

Похожие инструкции для BSR00034

Бренд: Yarvik Страницы: 222

Бренд: Moneris Страницы: 25

Бренд: Netum Страницы: 26

Бренд: Sunpak Страницы: 8

Бренд: Laser Страницы: 15

3800G04-USBKITE

Бренд: HandHeld Страницы: 144

Бренд: JMM Страницы: 13

Бренд: Linea Страницы: 17

Бренд: Jamex Страницы: 15

Бренд: Kobil Страницы: 3

Бренд: Infinite Peripherals Страницы: 31

SCRIBA 150 White 2 GB

Бренд: WOXTER Страницы: 1

Бренд: Sun Microsystems Страницы: 22

Бренд: Code Страницы: 15

CORTEXJPOS CR6000

Бренд: Code Страницы: 20

Code Reader CR3600 DPM

Бренд: Code Страницы: 106

Бренд: Sven Страницы: 4

Бренд: Sven Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды