Bryant 800SA Скачать руководство пользователя страница 19

Страница: 19 / 40

800SA/801SA: Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

The 24-v circuit contains an automotive-type, 3-amp. fuse located on the

control. Any direct shorts during installation, service, or maintenance

could cause this fuse to blow. If fuse replacement is required, use ONLY

a 3-amp. fuse of identical size.

ACCESSORIES

1. Electronic Air Cleaner (EAC)

Connect an accessory Electronic Air Cleaner (if used) using 1/4-in

female quick connect terminals to the two male 1/4-in

quick-connect terminals on the control board marked EAC-1 and

EAC-2. The terminals are rated for 115 VAC, 1.0 amps maximum

and are energized during blower motor operation (see

Fig. 28

2. Humidifier (HUM)

Connect an accessory 24 VAC, 0.5 amp. maximum humidifier (if

used) to the 1/4-in male quick-connect HUM terminal and

COM-24V screw terminal on the control board thermostat strip.

The HUM terminal is energized when the pressure switch closes

during a call for heat (see

Fig. 28

NOTE:

DO NOT connect furnace control HUM terminal to HUM

(humidifier) terminal on Thermidistat

, Zone Controller or similar

device. See Thermidistat, Zone Controller, thermostat, or controller

manufacturer’s instructions for proper connection.

A190023

Fig. 28 – Furnace Control

A200134

Fig. 29 – Thermostat Wiring Diagrams

24-V THERMOSTAT

TERMINALS

PL2

–

(115VAC) HOT SURFACE IGNITER &

INDUCER MOTOR 115V SUPPLY CONNECTOR

115-VAC (L2) NEUTRAL

CONNECTIONS

115-VAC (BL-1) BLOWER MOTOR LINE

VOLTAGE CONNECTION

EAC-1 TERMINAL

(115-VAC 1.0 AMP MAX.)

PL1

–

LOW VOLTAGE MAIN HARNESS

CONNECTOR

TRANSFORMER 24-VAC

CONNECTIONS

3-AMP FUSE

STATUS LED LIGHT

HEAT OFF-DELAY

HUMIDIFIER TERMINAL

(24-VAC 0.5 AMP MAX.)

BOARD PART NUMBER

LOCATION

COOLING SPEED

TAP

HEATING SPEED

TAP

PR-1

115-VAC (PR-1) TRANSFORMER

PRIMARY

J2 DEFEAT

JUMPER

TEST/TWIN

HEAT OFF-DELAY

JUMPER SELECT

PLT -FACTORY RUN TEST PORT

PRODUCTION USE ONLY

BL-1

115-VAC (L1) LINE VOLTAGE

CONNECTION

FAN SPEED TAP

Single-Stage Furnace with Single-Speed Air Conditioner

Single-Stage Furnace with Single-Speed Heat Pump

Содержание 800SA









































Результаты поиска

Содержание 800SA

Отзывы:

Похожие инструкции для 800SA

Бренды по названию

Популярные бренды

Bryant 800SA, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание 800SA

Отзывы:

Похожие инструкции для 800SA

Бренды по названию

Популярные бренды