Bryant 569J Series Скачать руководство пользователя страница 22

Страница: 22 / 56

C09022

Fig. 16 -- Weatherproof Cover Installation

All Units —

Voltage to compressor terminals during operation must be

within voltage range indicated on unit nameplate. See

Tables 11 and 12. On 3-phase units, voltages between

phases must be balanced within 2% and the current within

10%. Use the formula shown in the legend for Tables 11

and 12, Note 4 (see page 25) to determine the percent of

voltage imbalance. Operation on improper line voltage or

excessive phase imbalance constitutes abuse and may

cause damage to electrical components. Such operation

would invalidate any applicable Bryant warranty.

Field Control Wiring —

569J unit control voltage is 24 v. See Fig. 29 -- Fig. 31 for

typical field control connections and the unit’s label

diagram for field-supplied wiring details. Route control

wires to the 569J unit through the opening in unit’s end

panel to the connections terminal board in the unit’s

control box.

Remainder of the system controls connection will vary

according to the specific construction details of the indoor

section (air handler or packaged fan coil). Fig. 17

(569J***A/B) and Fig. 18 (569J***D/E/F) depict typical

connections to a Bryant 524J fan coil unit. Plan for field

connections carefully and install control wiring correctly

per the project plan. Additional components and

supplemental transformer accessory may be required.

The 569J unit requires an external temperature control

device. This device can be a thermostat (field-supplied) or

a thermostat emulation device provided as part of a

third--party Building Management System.

Thermostat —

Install a Bryant-approved accessory thermostat according

to installation instructions included with the accessory.

Locate the thermostat accessory on a solid wall in the

conditioned space to sense average temperature in

accordance with the thermostat installation instructions.

Note 1: Connect only if thermostat requires 24-vac power source.

Note 2: Connect W1 and W2 if supplemental heaters are installed

Note 3: Y2 connection for Single Circuit/2-Stage units only

Field Wiring

(Note 1)

(Note 2)

(Note 3)

(Note 2)

C150413

Fig. 17 -- Typical Remote Thermostat Connections

— 569J***A/B and 569J*07G/H

Note 1: Typical multi-function marking. Follow manufacturer’s configuration

instructions to select Y2.

Note 2: Connect only if thermostat requires 24-vac power source.

Note 3: Connect W1 and W2 if supplemental heaters are installed

Field Wiring

(Note 1)

(Note 2)

(Note 3)

C10078

Fig. 18 -- Typical Remote Thermostat Connections

— 569J***D/E/F

569J***A/B Unit -- 569J***A/B unit is a single--stage

cooling unit. If no economizer function is required, select a

single--stage cooling thermostat. If an integrated economizer

function is required, select a two--stage cooling thermostat.

569J*07G/H is a single circuit, two--stage cooling unit.

Select a two--stage cooling thermostat.

569J

Содержание 569J Series

























































Результаты поиска

Содержание 569J Series

Отзывы:

Похожие инструкции для 569J Series

Бренды по названию

Популярные бренды

Bryant 569J Series, Инструкция по установке, запуску и обслуживанию

Результаты поиска

Содержание 569J Series

Отзывы:

Похожие инструкции для 569J Series

Бренды по названию

Популярные бренды