Bruker Ascend 600'89 Скачать руководство пользователя страница 47

Страница: 47 / 102

ZTKS0174 / Z31966 / Rev.: 01

Troubleshooting

Continued from page before

Continued on next page

Indicator

Possible reason

Solution

Shorting plug can
not be removed.

The connector is
covered with ice
(frozen moisture or
nitrogen ice).

Carefully remove the ice with
warm helium gas. Use the
dipstick or the precooling tube
as tubing for the warm helium
gas to remove small ice spots
from the connector.

Bruker Service

The magnet system
quenches.

Loss of
superconductivity.

See chapter

”After a

Quench” on page 53

Bruker Service

The helium level was
too low for energiz-
ing, cycling,
shimming,
de-energizing or
sweeping.

See chapter

”After a

Quench” on page 53

Bruker Service

The Power Supply is
defective. The main
current is oscillating.

Replace the Power Supply.

Bruker Service

The main coil switch
can not be closed on
field.

The helium level is
too low for energiz-
ing. The main coil
switch is not covered
with liquid helium.

Never try to energize the
magnet with less than the
"minimum level during ener-
gizing" in the helium vessel.

Bruker Service

The Power Supply is
defective. The main
current is oscillating.

Replace the Power Supply.

Bruker Service

Shim current can not
be set correctly.

The control cable is
not connected
correctly to the
current lead or to the
Power Supply.

Connect the control cable
correctly to current lead and
power supply.

Bruker Service

Switch „Main Coil/
OFF/Shim Coil“ in
wrong position.

Change the switch position.

Bruker Service

Shims do not affect
the NMR signal.

Shim heater current
is not correct. The
shim switches are
not opened.

Set the shim heater current to
the specified value (see

Appendix Technical Data

Bruker Service

Содержание Ascend 600'89







































































































Результаты поиска

Содержание Ascend 600'89

Отзывы:

Bruker Ascend 600'89, Руководство пользователя, Страница: 47 / 102

Результаты поиска

Содержание Ascend 600'89

Отзывы: