Bruker Ascend 600'89 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 102

Bruker Ascend 600'89 Скачать руководство пользователя страница 13

13

ZTKS0174 / Z31966 / Rev.: 01

2

Safety

The supplied cryostat and further equipment of the magnet system were designed and
manufactured according to best available technical knowledge and practice, achieved in
over 50 years of experience of the Bruker Corporation. International standards for quality
and approval recommended for cryostats of superconducting magnets were certified.

Nevertheless non-compliance with the following instructions and safety advice may
cause serious hazards and property damage.

2.1

Approved Persons

Bruker BioSpin AG identifies the following qualifications for personnel performing tasks
on the magnet system or its components:

Approved Customer Personnel

As a result of professional training by Bruker Service Personnel, experience and
knowledge of applicable regulations these persons are qualified to perform the specific
tasks on the magnet system and its components assigned to them in this manual.
Approved Customer Personnel are qualified to identify possible hazards and risks
associated with the tasks assigned to them and to perform all possible steps to eliminate
or minimize these risks.

Bruker Service Personnel

These persons are qualified by appropriate qualification and professional training and
experience (including all necessary knowledge of applicable regulations and regulatory
requirements) to perform specific tasks on the magnet system and its components.
Bruker Service Personnel are qualified to identify possible hazards and risks and to
perform all possible steps to eliminate or minimize these risks.

«
...
11
12
13
14
15
...
»

Содержание Ascend 600'89







































































































Отзывы:

Нет отзывов