Bruker Ascend 600'89 Скачать руководство пользователя страница 42

Страница: 42 / 102

ZTKS0174 / Z31966 / Rev.: 01

Troubleshooting

6.2.3

During Cooling Down

a. see note on page before

Continued on next page

Indicator

Possible reason

Solution

Cooling with liquid
nitrogen continues
too slowly.

Empty transpor-
tation dewar.

Refill or replace transportation
dewar.

Bruker Service

Transfer pressure
too low.

Increase transfer pressure
slightly (max. pressure
0.3 bar).

Bruker Service

Transportation
dewar is leaky; no
transfer pressure
can be applied.

Check transportation dewar
and replace if necessary.

Bruker Service

Precooling with
liquid nitrogen
continues too
quickly.

Transfer pressure
too high.

Stop cooling. Adjust correct
transfer pressure.

Bruker Service

Vacuum in RT
vessel does not
reach
5 x 10

-5

mbar in

48 hours.

O-rings may be
leaky.

Check and clean O-rings and
slots; replace O-rings if
necessary:
•

of the Vacuum Valve

•

of the drop-off plate

•

of the reduction and
sealing flanges

•

of the bottom plate

Bruker Service

O-rings may be
frozen due to contact
with liquid nitrogen.

Stop cooling.

Warm up O-ring with
warm air

Wait until the vacuum
recovers.

Prevent liquid nitrogen
from splashing on
O-rings.

Bruker Service

Defective pumping
unit or pumping line.

Check pumping unit and
pumping line:
A vacuum less than 10

-6

mbar

must be reached with a
closed sealing plug.
Replace if necessary.

Bruker Service

Содержание Ascend 600'89







































































































Результаты поиска

Содержание Ascend 600'89

Отзывы:

Bruker Ascend 600'89, Руководство пользователя, Страница: 42 / 102

Результаты поиска

Содержание Ascend 600'89

Отзывы: