Bruker Ascend 600'89 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 102

Bruker Ascend 600'89 Скачать руководство пользователя страница 11

11

ZTKS0174 / Z31966 / Rev.: 01

1

Introduction

1.1

General Information

This manual contains important information about the handling of the supplied magnet
system used for NMR spectroscopy and its components. The compliance with all safety
and handling instructions, the applicable local accident prevention and general safety
regulations are necessary for safe work.

This manual is part of the product. It must be kept nearby the magnet system and free
access must be ensured at any time. Read the manual carefully before handling the
magnet system or its components.

1.2

Limitation of Liability

The information in this manual will take into account the current state of the technology.

The manufacturer assumes no liability for damages resulting from:

•

non-compliance with the instructions and all applicable documentation,

•

use for purposes not intended,

•

not sufficiently approved persons,

•

arbitrary changes or modifications and

•

use of not approved spare parts or accessories.

1.3

Customer Service

Technical support is provided by Bruker Service via telephone or e-mail. For contact
information see page 9 of this document.

1.4

Warranty

The warranty terms can be found in the sales documents of the magnet system and in
the Terms and Conditions of Bruker BioSpin AG.

1.5

Copyright

No part of this publication may be reproduced, stored in a retrieval system, or transmit-
ted, in any form or by any means without the prior consent of the publisher. Product
names used are trademarks or registered trademarks of their respective holders.

«
...
9
10
11
12
13
...
»

Содержание Ascend 600'89







































































































Отзывы:

Нет отзывов