BRP SEA-DOO GTI 130 2019 Скачать руководство пользователя | Manualshive

Страница: 161 / 204

background image

TROUBLESHOOTING GUIDELINES

ENGINE LACKS ACCELERATION OR POWER (cont’d)

8. Clogged injectors.

– Seek service from an authorized Sea-Doo dealer, repair shop, or person of

your own choosing for maintenance, repair, or replacement. Please refer
to the US EPA EMISSIONS-RELATED WARRANTY contained herein for
information about warranty claims.

9. Low fuel pressure.

– Seek service from an authorized Sea-Doo dealer, repair shop, or person of

your own choosing for maintenance, repair, or replacement. Please refer
to the US EPA EMISSIONS-RELATED WARRANTY contained herein for
information about warranty claims.

10.Water in fuel.

– Siphon and replace.

11.Engine damaged by water ingestion.

– Refer to an authorized Sea-Doo dealer.

WATERCRAFT CANNOT REACH TOP SPEED

1. Jet pump water intake clogged.

– Clean. Refer to JET PUMP WATER INTAKE AND IMPELLER CLEANING in

SPECIAL PROCEDURES section.

2. Damaged impeller or worn-out wear ring.

– Replace. Refer to an authorized Sea-Doo dealer.

3. Engine management system fault detected (check engine pilot lamp is

ON).

– Refer to MONITORING SYSTEM.

4. Faulty supercharger and/or intercooler (supercharged models).

– Seek service from an authorized Sea-Doo dealer, repair shop, or person of

your own choosing for maintenance, repair, or replacement. Please refer
to the US EPA EMISSIONS-RELATED WARRANTY contained herein for
information about warranty claims.

WATERCRAFT STAYS IN NEUTRAL AFTER OPERATING THE IBR LEVER (MODELS
WITH iBR)

1. The iBR gate stays in neutral.

– Release the throttle to idle RPM.
– Press the CRUISE button to activate the slow speed mode.
– Return to shore using the slow speed mode. Refer to an authorized Sea-Doo

dealer.

iBR WILL NOT RETURN TO NEUTRAL POSITION (IBR INDICATOR LIGHT ON)
(MODELS WITH iBR)

1. iBR jammed with debris.

– Clean and check for damage in the iBR gate and nozzle area.

______________

159

https://www.boat-manuals.com/

«
...
159
160
161
162
163
...
»

Содержание SEA-DOO GTI 130 2019













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEA-DOO GTI 130 2019

Bavaria 37 2017 Jitterbug

Бренд: Horizon Yacht Charters Страницы: 27

Бренд: Hobie Страницы: 36

Бренд: Delphia Страницы: 102

Бренд: YAMARIN Страницы: 40

Бренд: Scout Boats Страницы: 112

Бренд: Grady-White Boats Страницы: 78

Бренд: Grady-White Boats Страницы: 82

Бренд: Grady-White Страницы: 112

Бренд: Cape Dory Страницы: 94

Бренд: LaserPerformance Страницы: 22

Бренд: Dehler Страницы: 68

Бренд: Viking Страницы: 6

Бренд: Walker Bay Страницы: 24

Бренд: Lagoon Страницы: 39

MERRY FISHER 755

Бренд: Jeanneau Страницы: 110

sun odyssey 33I

Бренд: Jeanneau Страницы: 136

Бренд: Quicksilver Страницы: 45

Бренд: Quicksilver Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды