BRP SEA-DOO GTI 130 2019 Скачать руководство пользователя

Страница: 128 / 204

MAINTENANCE PROCEDURES

All Other Countries

XPS™ RECOMMENDED ENGINE OIL

900 ACE

130 and 155

230

4T 5W40 SYNTHETIC

BLEND OIL

(P/N 779133)

If THE RECOMMENDED XPS

ENGINE OIL IS NOT AVAILABLE

Engine

without

supercharger

Use a 5W40 4-stroke
SAE synthetic engine oil
meeting or exceeding
the following lubricant
industry specifications:

– API service

classification SJ, SL,
SM or SN

Always check the API
service label certification
on the oil container,
it must contain at least
one of the indicated
standards.

Engine

with

supercharger

Use a 5W40 4-stroke
SAE

motorcycle engine

oil compatible with
wet clutches

meeting

or exceeding the

both

following lubricant
industry specifications:

– JASO-MA2
– API service

classification SJ, SL,
SM or SN

Always check the API
service label certification
on the oil container,
it must contain at least
one of the indicated
standards.

Rotax

engines were developed and

validated using the XPS™ oil. BRP rec-
ommends the use of its XPS engine oil
or an equivalent at all time. Do not add
any additives to the recommended en-
gine oil. Damages caused by the use

of an oil not suitable for the engine or
by adding of an additives may not be
covered by the BRP Limited Warranty.

Engine Oil Level

NOTICE

Check

level

frequently

and refill if necessary. Do not over-
fill. Operating the engine with an
improper level may severely dam-
age engine.

CAUTION

Many components

in the engine compartment may be
very hot. Direct contact may result
in skin burn.

Oil level can be checked with water-
craft either in or out of water.

If Watercraft is Out of the Water

NOTICE

Watercraft must be level.

CAUTION

When operating the

engine out of water, the heat ex-
changer in the ride plate may be-
come very hot. Avoid any contact
with the ride plate as burns may oc-
cur.

1. Raise trailer tow pole, then block in

position when bumper rail is level.

2. Open the seat.

3. Install a garden hose on the exhaust

system flushing connector. Refer
to

EXHAUST SYSTEM

in this sec-

tion and follow the procedure.

NOTICE

– Never run engine without supply-

ing water to the exhaust system.
Failure to cool exhaust system
may severely damage it.

– Never run engine longer than

2 minutes. Drive line seal has no
cooling when watercraft is out of
water.

4. With the engine already at normal

operating condition, let engine

idle

for 30 seconds

then stop engine.

126

______________

https://www.boat-manuals.com/

Содержание SEA-DOO GTI 130 2019













































































































































































































Результаты поиска

Содержание SEA-DOO GTI 130 2019

Отзывы:

Похожие инструкции для SEA-DOO GTI 130 2019

Бренды по названию

Популярные бренды

BRP SEA-DOO GTI 130 2019, Руководство оператора

Результаты поиска

Содержание SEA-DOO GTI 130 2019

Отзывы:

Похожие инструкции для SEA-DOO GTI 130 2019

Бренды по названию

Популярные бренды